I'm working on an Android app that connects to a Nordic nRF52833 BLE peripheral (Zephyr 3.7.99 / NCS 2.9.0). I'm encountering a consistent issue where:
The app connects...
I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hi
We are investigating Hong Kong certification for our nRF9E5 based equipment in the 868 band
The snag seems to be that required channel centre frequencies are "odd...
Hi,
My setup is a nRFgo QFAA FA with S110 v.6.0.0 and Motherboard. I am using the latest SDK 5.1.0. The Master Control Panel drives the nrf51822 USB development dongle...
Hi,I have a Nrf8001 module, use a arduino to control it.
Now,I can use this module to connect IPHONE APP(BLE Probe and LightBlue),sending and reciving data are all ok,the...
Hi Nordic Devs,
First, thank you for excellent documentation and sample code for use with your hardware. It's been tremendously useful already!
I'm pleased to own an...
Hi,
i have some trouble with my watchdog in application. If i does a System_reset (no SD Method because i disabled it before) it sometimes top at this point and does nonsense...
Hi,
We'd like to using nRF51822 to setup an environment which have 2 peripherals and 1 multi-connection central.
Peripheral 1 : reading some data from the car(OBDII...
Hi, we add two characteristic as TX/RX.
We are ready to use them to transmit data and receive data with phone
One for transmit the control command and get respond command...
We have hardware that uses the nRF905 transceiver that inputs different addresses into the nRF905 TX messages based on the specific unit (TX_ADDRESS varies based on unit serial...
Hello
We have devices who uses nRF905 for transmissions between them. When we receive messages we use the AM and DR signal to determine if a message is read correctly. The...
GPIOTE gives us 4.
LPCOMP gives us 1.
What else?
I am working on something related with external interrupts.
Doesn't have problem in my project, but I just always...
Hi Guys,
Is there a way with the Keil C Compiler to get an *.LST file or some sort of Assembly output from C source input?
I'm still trying to write some code to drive...
Hi
Now, I am coding SDK5.0.0 keyboard project and almost done. It's Keil C version. Did you have IAR version for reference? Besides, did you know if IAR supports J-Link lite...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
I would like to know how to implement reset button on nRF51822. Image of schematic would be very useful, but good explanation should be enough. Thank you in advance.
I...
