Hello everyone. I am trying to develop a emulator for a Bluetooth low energy tv remote using raspberry PI. Basically I want to be able to use the raspberry pi as a TV remote...
Hi, I have changed Vdd from 1.8 V to 3.3 V but now I cannot flash anymore my board (nrf5340). This is the output error:
* Executing task: nRF Connect: Flash: AppCore_RHS_SD_UI_v1B...
Is there a BLE development board that supports extracting IQ data from raw MCPD ranging？ Does nrf5340dk support users to extract IQ data for the development of ranging algorithms...
Hello Nordic Support Team,
I am working with the nRF54L15-DK and testing the Bluetooth Direct Advertising sample application (based on Zephyr). I am measuring current consumption...
Hi, the nordic team
I am working on thread protocol using SDK version 2.9.1.
I use the SED device,My poll is 1000 ms. How can I receive messages from my parent node when...
I have enabled all the dependencies asked as below
CONFIG_IMG_MANAGER =y
CONFIG_STREAM_FLASH =y
CONFIG_BOOTLOADER_MCUBOOT =y
CONFIG_DFU_TARGET_MCUBOOT =y
Still...
Hello,
I am using the nRF5340 in my project, and the device is capable of communicating with a mobile phone over BLE . However, we occasionally encounter a connection error...
I am currently working with an NRF51822 and managed to change the TWI frequency to 400kHz in the twi_hw_master (this worked, I can see it on the oscilloscope). I commented...
I'm trying to upload via DFU from one nRF52832 to another nRF52832
I use SDK 14.1
First I want to enable CCCD at the master side.
static uint32_t cccd_configure(uint16_t...
Dear Sirs,
We are evaluating nRF52840 now, How far is the maximum range it can reach while keeping the data rate at 2Mbps if we use two nRF52840 for point-to-point communication...
i've been trying to generate hex files using keil uv5 from the examples given in the nrf52 sdk, the pregenerated hex files work as expected, wheras the ones generated by keil...
Dear Nordic Team,
Thanks for supporting.
I want to know How to add Manufacturing data with whitelist advertising . Already i am implemented without whitlist advertising...
Hello Team,
I have developed a sample Android application to use and control Nordic Thingy 52. I am able to control LED (Constant, Blink, Intensity). But I am not getting...
I want to test the mesh network for that i have to set the radio range of node to minimum distance so that i'll able to test the relay node example. Will you please help me...
Hello I am trying to make an electron application which is based from the 'pc-ble-driver-js' module for testing pupose for production development with nordic product
I am...
Hi all,
I using NRF52 kit and NUS service . When I add bond on NUS service , I still using nomal and I do not see the difference before and after I add bond . So , I want...
Hi. I am going down a rabbit hole. Wish to work with the SDK for Mesh using ideally the PCA10040 (nRF52832) and PCA10056 (nRF52840) kits.
1) Is this possible to mix the...
Hello,
I use the nrf51 with SDK 12.3.0.
I followed the tutorial for custom services and added characteristics as described here: https://devzone.nordicsemi.com/tutorials...
Referencing another trouble ticket
https://devzone.nordicsemi.com/f/nordic-q-a/22621/hardfault-on-an-sd_ble_gatts_hvx-call-in-sdk12-3
I am experiencing the same issue...
I'm trying to implement send && recieve through one wire. Handling of pin state, if it is input or output is done via SW. Also it is going to be half-duplex only.
Is it...
