Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Is there any way to sniff BLE 6.0 packets and see the new content such as channel sounding? I am familiar with the nRF52840 Dongle as a sniffer in Wireshark, is there similar...
Hello,
I´m trying to measure the current consumption on the nRF54L15-DK Rev. 0.9.2.
There are a few questions:
1) What is the role / purpose of the voltage buffer? ...
Hello, I have an issue regarding the current measurement of my nRF7002DK_nRF5340. I am trying to measure the current consumed during the transmission of a carrier on a Wi...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I’m writing this post because I’m experiencing a problem with data transmission between two devices—a sensor and a USB dongle connected to a PC—each equipped with a Minew...
I used nrf8001 to implement ANCS.It working fine.But when it disconnect for a while and reconnect(reconnect successed).I found Iphone can't send any ANCS message to nrf8001...
Hi, I would like simplify the nRF24AP2-8CH signal RF output using a Balun with a chip antenna.
What is the best way: the 2450BM14A0002 from Johanson, the BAL-NRF01D3 from...
Hello all,
I have nRF51822 and after one attempt to use it as a sniffer I have erase the demo app or everything else on it. Since then I was unable to turn back as it as...
Hi,
I need to make it possible to allow connection to one specific central device. This with the thought that the user doesn't want to be bothered with bonding the device...
Hi,
I am having trouble in downloading firmware to my development kit. Previously, everything worked and the module already flashed with my BLE firmware. Today, as usual...
I wish to inform Nordic about this issue with jlink OB used on EK boards when used in OS X environment.
J-link OB returns " Can not connect to J-Link via USB." and a CDC...
Hi all -
I just received my nRF51422 V2 eval kit, eager to try it out.
I am fairly convinced I have all the latest nRFGo and SDK installed, fresh off the Nordic site....
my application is based on the BLE example: ble_app_hrs.
it works well before, but when I add some functions to configure the GPIOTE , and then download to the Device, it...
Hi,
We survey APPLE's ANCS right now!
But we have a question that need your help
We see the sample code experimental\ble_app_ancs
There are 1 base uuid and 3 service...
I'd like to have a short email dialogue with someone familiar with Arduino programming. Probably not a suitable forum topic; would someone be willing to email me? or.. message...
This is my first time working on Nordic-made IC.
My previous experience is on PIC which has its own compiler (relatively cheap at 200$). I'm shifting to nRF51822 development...
I am using soft device S110 ver 6.0.0 with nrf51822. SDK version is 5.1.0. Reading the source of SDK, I see that it must be possible to create multiple hid services. I am...
Hello,
after programming the nrf51822 the SWDIO/nRESET pin is in "debug mode", to resume the normal mode the SWDCLK and SWDIO/nRESET line shuold low for a minimum of 100...
