Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
Device- nRF52832 (nRF52 DK)
SDK version 14.2
SoftDevice version 5
Segger embedded studio.
I am trying get the BLE working, unfortunately calling nrf_sdh_enable_request...
Hi, Everyone How to turn on 4 LEDs in BLE ? I am testing ble_app_uart on nrf52832 (softdevice s132). Try to blink the four LEDs on the board do. I have added to main() bsp_board_led_invert...
Hi,
I want to create a custom GATT service. So I duplicate the example from the SDK ble_app_blinky. Basically what I did so far is rename all the "LBS" (ble_lbs, lbs_p,...
Hello, I am trying to store microphone data from the Nordic Thingy by modifying the Nordic Thingy Android app .
The Thingy firmware encodes the digital microphone data...
Hi there,
First of all, I'm pretty new to this, so next question might be obvious to others.
I try to decipher a line of code, and the little Part is what puzzles me...
I've created 2 custom PCB boards, 1 main board and 1 dongle based on the nF51822. The Dongle board uses the default ble_app_uart_c code. The main board transmits to the Dongle...
Hi,
I'm developing a new product. I want to manage power ON/OFF with the button. I see 2 solutions.
1) Using a pushbutton controller (like ST SRC0) -> Adding 0.5$ to...
Let me first apologies as I am a real novice with these types of items.
But your help in my issue will be greatly appreciated.
We are currently using nRF51 USB dongles...
Hi,
I have nrf52 Thingy board and i want to read temperature sensor data using twi sensor example available in SDK 11. I am not able to get data.
Thanks
Hi Support team,
I am looking to replace my BLE chip by a nRF8001. I am currently using a DA14580 (Dialog Semiconductor), in Beacon mode or pairing mode. I saw that the...
Hi,
As given in the link: http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.tools%2Fdita%2Ftools%2Fpower_profiler_kit%2FPPK_user_guide_Troubleshooting...
Hi, would you support with the following:
In the high voltage mode (defined as when the supply voltage is only connected to the VDDH pin and the VDD pin is not connected...
