I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hello, I am running bluetooth example.
I am using the nRF52832 board and SDK 14.0.
I modified the multilink example to make a slight modification and connect it to another...
I have a windows side application and an Android App, both of which are set to capture data from the Thingy Sound Service.
On the windows application, the data after being...
I need to be able to reserve some flash to permanently store manufacturing values that will never change. I did this on an nRF51 by reserving a 4KB block and setting the necessary...
Hi all ,
I have problem . I have 1 NRF52832 dev kit . It connect to STM32 devkit via UART . I want to tranfer firmware of STM32 from smartphone to NRF via BLE , and from...
Hi,
I added this in SystemInit() (just below the CONFIG_NFCT_PINS_AS_GPIOS section) within system_nrf.c so that I could easily turn on or off the APPROTECT read back protection...
I am using Thingy 52 and I need to use multiple sensors on the board. But the API reference is really poor and there is no examples on this. So I don't know how to configure...
I'm trying to debug a high current issue on a custom board based on the nRF52832. I'm currently loading a modified blinky app (entire main.c included below). On the nRF52DK...
hello,
I am using nrf52 DK and MPU 9255 .I am using source code given here here .of this link,I have taken 'nrf5-ble-data-ready-interrupts' example .code builts fine in...
Hi all,
I have a Thingy52 and a nRF52-DK.
I have successfully setup 2 different Eclipse projects to compile code for both hardware.
On the nRF52-DK, i was able to build...
I am developing Firmware for NRF51822, S110 in Eclipse. I Heard that there is two mode in Firmware. 1. Debug mode 2. Production(release) mode. Is there anything like that...
Hi,
Currently I am browsing the mesh sdk to get enough information for my own implementation,
However sometimes its quite difficult to see what a C/H file actually does...
Hi,
I am trying to use nRF52832 dev kit(pca10040) as my connectivity board and STM32L4 as my application board. I have flashed ser_s132_uart(examples\connectivity\ble_connectivity...
Hi,
I have seen alot about the declaration process with the Bluetooth SIG but couldnt find my specific case.
We made a BLE application with the NRF51, a PCB Antenna, SD130...
I haven't found specific documentation on this so I would like to be absolutely certain that the fields in the softdevice info structure are used how I think they're used...
