Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I looked at the radio project in the peripheral folder on SDK5 11. I managed to get a custom radio project that works well with my device. A brief on my project, I set up...
Hi
I have set the nRF Beacon app to action a Tasker task when the phone is "At the beacon".
The app display the following: "An error occurred when launching the task"...
hello
i am using nrf52 board.is there any tutorial to setup the Template project in Visual GDB for the custom design project.i alread test the blinky and the result was successfull...
Hello
I am using this tutorial blog.blecentral.com/.../
to configure my BLENANO to work on eclipse whith gcc toolchain.
I am using the latest SDK which has the softdevice...
Hello,
I can't solved a problem with advertising problem on my iBeacon working on nRF51822.
I have my own 40 unity BLE Module in my room test. They're configured to...
Hello,I run the program nRF52_SDK_11.0.0\examples\peripheral\uart\pca10040\arm4
and rewrite the "main":
int main(void)
{
//LEDS_CONFIGURE(LEDS_MASK);
//LEDS_OFF(LEDS_MASK...
Hi,
nRF5_SDK_11.0.0_89a8197\examples\peripheral\saadc\pca10040\arm5_no_packs
Which timer is used in this example? RTC timer or Timer0-4 ?
I can not find it.
Thanks...
Hi,
I have used nRF51 DK board for 6 months well.
Then now, it isn't connected with nRFgoStudio since I have upgraded nRFgoStudio about 1 month ago.
Error message is no...
Is there any reason I can't have the radio notification run at priority 0? By definition it will never run at the same time as the lower stack, so it seems like I should be...
hi nordic
Have a code project sample shows the typical use Flash applications in data storage?
I see
[code]( infocenter.nordicsemi.com/index.jsp .
my code
`
#define...
If I have a high-priority interrupt (or a series of them) that runs long enough to completely mask a radio notification, then all further radio notifications appear inverted...
I bought two EZAIRO 7150 SL hybrid board, (which contains a MOTHERBOARD & DAUGHTERBOARD). As part of the problems we have been having trying to establish a wireless connection...
Hi, I am developing a software that connects to nRF51822 over UART. I donot have the physical device currently so I downloaded its Soft device under the impression that it...
Hi,I update my MDK from 4.7 to 5.0,my old project can open ,but can't find the device list.I want to use 5.0 and 4.7 at the same time,and I have installed the SDK6.0 when...
