I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
Hi,Team,
I am developing pawr using nrf54l15-dk. I wanted to set the parameters of pawr with 128 sub-events and 8 response intervals, but the setting Failed and the error...
I want to test the demo https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo that requires Mesh 1.0.1, but I do not seem to find it anywhere. Can someone point me...
Hi, guys! I am working about a project that I need to get data from sensor and send these data through mesh. I referred from link text ,and the example works well. But, I...
I'm looking for a Nordic expert. I have already designed and built a complete PCB based on the Nordic nRF52832, along with the firmware. I need to improve the PCB design,...
On my nRF52 DK, I'm seeing *something* pull down VCC by about 50 mV once every millisecond (1KHz), and I'm trying to identify its source. (This is only important because using...
Our application needs to read 128 bytes from 6 SPI sensors as efficiently as possible. We're currently using a single SPI Manager to read all 128 bytes from all 6 sensors...
Hi all.
Just wondering if i need to go through the tutorials on making a service if i just want to read a few bytes in an advertising beacon.
I'm a little lost on figuring...
Hi ,
I am using a bluetooth peripheral which have the Custom Service ID and characteristics ID as below.
Service UUID: 56494B01-0100-1000-8000-00805F9B04E1
Characterisitics...
Hi,
We are currently developing an application that makes use of soft device(s112). We tried using timer(Timer 1) for a timed wake up and sleep but found that the actual...
We are seeing an LMP PDU error when connecting to a Nexus 6p with Oreo (8.0.0) when connecting to an nRF52832 utilizing SDK 14.2 and either s132 vs 5.0 or 5.1 anytime NRF_SDH_BLE_GAP_EVENT_LENGTH...
Been testing custom_ble_service_example , specifically to see if a two byte custom_value can also be used.
But when setting custom_value to uint16_t I get a warning at this...
Hi, I would like to use a PWM application with mesh SDK. However when I try to compile, I got an error because "app_pwm.h" is missing (No such file or directory). The only...
Hi !
I'm using the nrf52832 chip and I'm trying to communicate with a LIS2DH12 accelerometer using the I2C protocol.
But unfortunately I can't handle with it, it seems...
Hello,
I am completely new to creating a Bluetooth mesh network and nRF5 devices. I have three nRF51 DK and 2 nRF51 dongles. I have earlier read the posts and made nRF51...
Hello,
I am using sdk12.2.2 and customised nrf52 board. I am writing 6000 records of 24 bytes each in flash of nrf52. My challenge is after 6027 records I am getting error...
