We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
Hello Nordic,
I am running a project, use the chipset is nRF54L15, I want to know if there is any USB dongle with software can be used to test BLE function of chip nRF54L15...
Hi everyone, I'm working on a project with Zephyr (v2.9.1) and I'm facing a compilation issue related to managing two SPI devices on different buses ( spi0 and spi2 ).
In...
Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
I am using NCS 2.7.0
i am running this build command from a terminal in VSC for the nrf/samples/bluetooth/Direction_finding_connectionless_tx sample
west build -p -b nrf5340dk...
HI,
I’m using nRF Connect SDK (NCS) v2.8.0 with the blinky example.nrf54l15dk, In the project, I configured the following in Kconfig:
kconfig
CONFIG_FPU...
Hi Nordic team,
My nRF52832 DK (PCA10040) was working perfectly until recently. Suddenly, it stopped getting detected by my PC.
Current Issue:
The board does not...
Hello Nordic Team,
I’m using the nRF9151 DK board in Surat, Gujarat, India with a valid Onomondo SIM card . I’ve followed the setup instructions as per the Nordic Academy...
Hello, I am trying to update the modem firmware to v1.3.7 using UART using the nRF modem bootloader API. For context, I am running nrf-sdk 2.9.1 and also using the SLM application...
Hi,
We’re working on a device using the nRF52832 and have DFU over BLE working correctly using internal flash. Updates work both via our custom app and the nRF Connect app...
Hi,
I believe 2M and 1M are OK to adjust, however, long range code added the extended advertisment, I am curious whether I can update these three PHY all together.
Thank...
Hi
I noticed one ticket says that "the following combination offers low power consumtion and high througput when needed :Short Connection Interval + High Slave Latency ...
Hi, I'm a beginner and I'm trying to run an LED blinking program. However, I'm encountering a device-related error.
I've followed tutorials and installed all the necessary...
Hi everyone,
I use the ble-app-buttonless-dfu example to develop my application.
I make a mutual authentication to be sure the device is connected to the right mobile...
Hey folks,
i have to use the nrf9160 board to create a PoC for a project of our company. The main topic of the PoC is not important here because i cant even connect to an...
