Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi
We have a product with Nordic nRF9E5 coupled to Texas CC1190 amplifier.
We are seeing transients at start and end of TX; worst at end. We appear to be non-compliant...
Hello, we are using SDK 5.2.0, SoftDevice 6.2.1 S110 on the peripheral side and S130 on the central side.
We have implemented a serial data link between the two, the central...
I have made a custom PCB with the nRF52832, following the circuit reference, I used the C3 and L1 for tunning the antenna. Instead of a chip antenna I placed a wire in the...
The NRF_LOG library apparently uses memobj, which uses balloc. I assume that means I need to add some blocks in my sdk_config (i.e., MEMORY_MANAGER_SMALL_BLOCK_COUNT, etc...
Hello Guys,
I have some measurements for the determination of the maximum range and the energy consumption. The experiment is based on the ATT_MTU throughput example, nRF5_SDK_14...
Hi,
We have a BLE peripheral device that is used as a mouse/keyboard (nRF52832 SDK 14.0)
The peripheral pairs with most central devices just fine (including Mac and PC...
I have two nrf51 development board. A is PRX, B is PTX. now B can send payload to A , and A can receive and response it by ACK. But some times A want to send payload to B...
hi Nordic support team ,
i have sent my application data to nrf connect .I want to send that data when i write something in "write value " option in nrf connect .After comparing...
Could anybody help me with some useful stuff and links to start programming from scratch for nrf52832 DK on Keil v5. I have some of my undergrad students who need this help...
Hi, guys, I tried nRF5_SDK\examples\ble_peripheral\experimental_ble_app_eddystone example on nRF52832 and it works perfect.
And I compared the code with the normal BLE advertising...
I got this info when I use keil to download progream though jlink.my board is NRF52832,the version of my keil is V5.24 and the version of my SDK is 14.0.
why it's happened...
Using SDK 14.2.0 and PCA10056 Dev kit: when I load the example (usbd_cdc_acm) and flash it, it works well, can communicate in both directions (windows 10 and debian linux...
During more than two years SDK contains OTS in 'experimental' mode. Do you have any plans to update this service (and write an example how to use), or better avoid using this...
Hello,
I updated Segger Jlink software to the last version and there is an issue with the nRF52840 preview DK.
Segger gives popup about updating firmware but it cannot...
I wonder if Nordic reveals electrical schematic of IO buffers?
I have taken some current consumption measurements recently and I have realized that setting a pin as input...
