Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
I'm trying to program my custom board with a PCA10056 following this scheme (Note that my custom board is powered by the PCA10056) :
VDD (PCA10056) ---> VTG(PCA10056...
Hi,
I'm using nRf52840 rev B and C chipset and not able to detect the NFC on the device (the rev A chipset is working). Following SW combination is used:
nRF5_SDK_15.0...
Hello,
I am working on Multi-link. I want to scan the advertising information and connect only the uuid I set up.
I want to process it on_adv_report (), but I do not know...
The output order of my scanning Saadc is not predictable.
I found two related questions, but they both are for SDK 11 and seem to have been resolved.
devzone.nordicsemi...
Hi,
Am I right that after provisioner done with network configuration all nodes save their info in persistant storage and continue work without a provisioner?
How provisioner...
HI
i'm trying to use TSL2561 sensor, but i can't geting to work. I found the code that works on the psoc that, I change it so it fits nrf52840 but it still does not work...
I want to be sure about erasing flash. Flash is divided into pages and each page has 8 blocks. The smallest amount of flash you can erase is a PAGE. Is this correct. In other...
hello,
I'm currently stuck with sd_app_evt_wait() function leaving for an unknown reason. This function is called in the main loop.
The only reasons that shall exit the...
BLUETOOTH SPECIFICATION Version 5.0 | Vol 3, Part H page 2321 Figure 2.4
According to the figure, if an eavesdrop device exists in the pairing process, it is easy to obtain...
Hi support team,
I am currently working with the nRF8001 that I wanted to integrated on a my PCB.I would like to know if you have an antenna to recommend to work with the...
Hi everyone!
I inherited an product already in production using the nRF51422 QFAA Ex0 chip with the S310 V3 stack. I checked the compatibility matrix and found out the Ex0...
Dear Sir/Madam,
I tried to use GPIOTE and nrf_dev_gpiote at same prject on a MDK 5 project which is based on nRF5 SDK 10 and SoftDevice S110, but got this error:
.\_build...
HI, I found that the maximum number of connections 52832 can only be 15 connections, like this
// <o> NRF_SDH_BLE_CENTRAL_LINK_COUNT - Maximum number of central links....
Hello, everyone~
I need to connect nRF51822 and another big MCU with SPI. The big MCU is connected to a LTE module. The new firmware of nRF51822 need to be downloaded...
