I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
We need to sample two digital inputs GPIOs at rate of 100khz-1mhz. How can we do that?
The QDEC is only good for up to 128us (~7khz) which is too slow for us.
Is there a...
I'm not able to get clear/un-corrupted data across the ttyACM on the nrf52840-PDK. I must be missing something, seems like this would have been solved a million times, but...
I recently experienced an issue with a race condition between peer manager and FDS in SDK 14.2 which was resolved under this case:
https://devzone.nordicsemi.com/f/nordic...
Hello,
I develop entirely on Linux and I am unable to find the --sd-req / --sd-id required for generating a dfu package zip using nrfutil . I am using developing for the...
I defined custom service (NRF51822,S110) to send sensor data. Code follows. Here I enabled notifications for new data. I can able to receive data, if I enabled notification...
Hi,
I have the following set up:
The remote: nrf51822 acts as central
The wheels: Each wheel has nrf51822 acting as peripheral.
The remote needs to first connect...
My application needs to be notified of large current draws due to the activity of the nRF8001. The active signal works fine for this purpose, but why is it available only...
What is the typical expected receiver sensitivity when performing BER test (1Msps, 16 byte packets) of the radio module ? The spec refers to 2 values: -93 and -96 dBm (p.231...
Hello,
We are considering merging the Eddystone and iBeacon features together, packet types toggling at each interval tick, then we assumed that we should take the Eddystone...
My device is sending a beacon under DEBUG, but not under RUN.
The issue started when I converted the scan_and_forward example to use a 16-bit device address.
It steps...
Dear Sir or Madam,
I'm using a dev kit with the nRF52832 to realize a project in school. So my work contains two wearables and both include the nRF52832. Now I want to communicate...
Hello,
is it somehow possible to calculate the distance of a BLE enabled and advertising periodially cell phone to a turnstyle gate.
There are for example 10 turnstyle...
Hello,
I'm trying to update from Mesh SDK 1.0.0 to 1.0.1, I've followed http://infocenter.nordicsemi.com/topic/com.nordic.infocenter.meshsdk.v1.0.1/md_doc_getting_started_how_to_nordicSDK...
Hi all,
I would like someone give me a suggestion about timers.
in my current approvement I am using an RTC timer with 32k crystal to control my sleep times it is power...