Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
Hi everyone!
I want to implement SPI with "ble_app_beacon" example with the following hw/sw.
DK : nrf52832
SDK : nRF5_SDK_14.2.0_17b948a
IDE : Segger Studio 3.34...
Recently,I use the SDK14 to develop the project,the initial project is in the content "SDK14/examples/peripheral/twi_scanner/pca10056",
Then and the spi example in the content...
I have build the light switch demo, it works properly. But I want to make multiple sensor node that takes data from sensor and send to single relay node. I am little confused...
I just integrated CMock which is part of my unit testing framework and i am trying to test a mocked function however i am running into RAM overflow error. Is there a way to...
May need to post this question to Segger, but I'd figure I'd ask here.
Have a nRF52832 project that compiles, links, and runs fine on the 52832/10040 dev kit board.
...
Hi All,
I am using the nrf52840 to run an application which does not use the BLE.
I need to add firmware update capability to the device so that I can push updated in...
Hi, I am running into a connection problem with connecting to the Secure bootloader example in SDK v13.1, whenever I try to connect I get Gatt 133 error. To my memory, the...
hi,
i doing a project where i have combined light switch server from nrf_mesh sdk 1.0.0 with nrf5 sdk 14.2.0 ble_uart_example to send.
my aim is to send on_off command...
We currently have an application that is running SDK 12.1 on the NRF52832. We have no issues doing a firmware update using the iOS SDK. What we are seeing is a long delay...
Hello, I am running bluetooth example.
I am using the nRF52832 board and SDK 14.0.
I modified the multilink example to make a slight modification and connect it to another...
I have a windows side application and an Android App, both of which are set to capture data from the Thingy Sound Service.
On the windows application, the data after being...
I need to be able to reserve some flash to permanently store manufacturing values that will never change. I did this on an nRF51 by reserving a 4KB block and setting the necessary...
Hi all ,
I have problem . I have 1 NRF52832 dev kit . It connect to STM32 devkit via UART . I want to tranfer firmware of STM32 from smartphone to NRF via BLE , and from...
Hi,
I added this in SystemInit() (just below the CONFIG_NFCT_PINS_AS_GPIOS section) within system_nrf.c so that I could easily turn on or off the APPROTECT read back protection...
I am using Thingy 52 and I need to use multiple sensors on the board. But the API reference is really poor and there is no examples on this. So I don't know how to configure...
