Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi,
I am using nRF51822 spi as a master to communicate with the AFE. Four bytes need to transfer each read or write process. I use nRF51_SDK_10.0.0_dc26b5e.
Configuration...
hi
I am trying to gather information on what is needed to create a mesh network using BLE.
I am more familiar with Zigbee/Thread, but I am asked to implement something...
I downloaded S212 for nRF52 from thisisant.com and programmed the softdevice to nRF52832DK(PCA10040) via nRFgo Studio. Then I copied the 'include' folder of unzipped softdevice...
I have been trying nrf-sniffer with no success. Setup is:
Win7 64,
Sniffer Win 1.0.1,
Wireshark 1.10.14 (both win32 and 64 tried),
PCA10000 and PCA10001
The sniffer...
I generally upload codes from mbed.org to my PC then send the hex file to nRF51822 by nRF51-DK's pins. But I don't want to use cables to upload hex codes to nRF51822. Are...
Hi community,
When I want to use the example multilink peripheral inside the s120 directory example of the SDK 6.1.0, I'm not able to compile the code.
The device_manager_peripheral...
So, I want to make an application where my NRF52 advertises an URL via the Eddystone beacon.
The URL will link to an webpage, that will connect to my device through the physical...
As here said link1 If we want to use flash in the mesh we should ignore APP_ERROR_CHECK(NRF_ERROR_INVALID_STATE) in ts_sd_event_handler() ,
2.And here link2 tell us...
How do I set up a variable length characteristic which is greater than 20 bytes and use notifications with this characteristic?
For example I have several variable length...
In an nRF51-based application I'm working on, I am using the SPIS peripheral and a generated clock signal to send a large buffer out over serial using DMA. I want to use the...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
hi
in tutoriall service beginer there is
static void advertising_init(void)
{
uint32_t err_code;
ble_advdata_t advdata;
// Build advertising data struct to pass...
wireshark 2.0.3 which is what got installed when I downloaded it is not supported according to the nFsniffer program.
So what, and how do you set this up?
I am using a function to read the die temperature data from nRF51822 as follows:
static uint32_t temperature_data_get(void)
{
int32_t temp;
uint32_t err_code;
...
