hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
On future revisions of the nRF52840 Dongle, and on future development hardware of a similar form factor, I'd recommend putting a debug connector that's compatible with the...
Nordic published a great blog in 2022: "Comparing range with Bluetooth Low Energy of the nRF21540 DK and the nRF52840 DK." It clearly explains the range capabilities of the...
I'm using Zephyr/NCS v2.7.0 with a custom multi-image project based on sysbuild . My top-level project has a sysbuild.conf at the root, and a sysbuild/ folder containing a...
Hi Nordic team,
I'm trying to stream audio from the nRF5340 DK to a BLE headset ( Sony inzone buds) using the [ Unicast Audio Client sample ] with the BAP profile.
Initially...
Hi everyone,
I'm using the nRF Connect SDK 3.0.2 and the nRF Connect Toolchain 3.0.1 with the matter ‘light_bulb’ example. I just want to do the following: 1) Get exactly...
When Enabling an advertising set already enabled on the Softdevice Controller, the HCI error command disallowed is produced when according to the BLE specification 6.0 it...
Hello, question about mcuboot, particularly the imgtool.py.
When I run west build, the build eventually fails on:
Error: Image size (0xbac8) + trailer (0xc30) exceeds...
Hello Nordic Support Team,
I have three queries to make.
Is it possible to force the channel in which the data transmission is happening using nRF52840 DK.
To explain...
Hello,
I am currently using the nrfutil application to convert modem trace logs to pcaps through an automated process. I am seeing intermittent failures with the following...
Hello, I'm using nrf9151-DK kit and this UDP example: UDP . After compile and flashing I opened both serial monitors (VCOM0, VCOM1) but no output appeared. Could you please...
Hi.
We are doing automatic network attaching on nRF9151. This is how the flow looks:
AT%XBANDLOCK=2,...
AT+CFUN=1
AT+COPS=0
We do this until we get registered...
