I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I've been looking for information on GCC support for the DFU bootloader examples in SDK v7.2.0 for the BLE Dongle board(PCA10031) but unfortunately there's nothing in the...
Hi
I'm testing the nRF Toolbox for Android. But I get this error when I try to connect using the proximity feature:
I'm using the nrf51822 EK with the s110 ble_app_proximity...
Hi Nordic Guy,
I'm trying to fine tune my connection parameters for better battery life, while at the same time trying to keep them within Apple's guideline. I notice in...
Hello guys, I'm going to start programming for nRF51822 and I want to ask you something.
I'm going to start coding for mbed HRM1017 which is the simplest eval board I found...
I'm attempting to use a custom UUID as outlined in nAN-36. I get an error (NRF_ERROR_DATA_SIZE) when I call ble_advdata_set . Specifically:
ble_advdata.c::uuid_list_encode...
I have a bluetooth hub (NRF51) as central and a wearable device (NRF51) as peripheral. What I need is that as soon as a smartphone enters the range the peripheral let's go...
Hello,
I'm redrawing and routing my own PCB for nRF81x22. I take the details from pca10028 files.
My question: Can I route the PCB with only 2 layers?? I have seen only...
Hello,
I had to use sd_ble_gap_address_set() to make sure, that a bootloader running on the same device will not be cached on OS/X:
static const ble_gap_addr_t gap_addr...
This may be a newbie question, but it had puzzled me for a while now.
Looking at the PCA10031's schematics i can see two leds been used.
LD2 i can figure out. Datasheet...
MQTT Example in the IoT SDK compiles with size bigger than available 160KB Program space?!! Is this correct as I can't flash with the IoT SoftDevice on it.
The drive level of the nRF51822 is specified as 1µW, whereas the EPSON crystal suggested in the BOM for the EK boards PCA10000 and PCA10001 is specified for just 0.5µW (with...
hi nordic
i just got a little bit outdated "nRF51422-dk" package. I have problems with flashing
the boards pca10006 and pca10007- I tried to search for an solution, tried...
Hi all,
I'm an Android developer and I need to develop an application that detect when someone presses the button on Beacon and do something.
I've just bought these two...
