I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello guys, I'm going to start programming for nRF51822 and I want to ask you something.
I'm going to start coding for mbed HRM1017 which is the simplest eval board I found...
I'm attempting to use a custom UUID as outlined in nAN-36. I get an error (NRF_ERROR_DATA_SIZE) when I call ble_advdata_set . Specifically:
ble_advdata.c::uuid_list_encode...
I have a bluetooth hub (NRF51) as central and a wearable device (NRF51) as peripheral. What I need is that as soon as a smartphone enters the range the peripheral let's go...
Hello,
I'm redrawing and routing my own PCB for nRF81x22. I take the details from pca10028 files.
My question: Can I route the PCB with only 2 layers?? I have seen only...
Hello,
I had to use sd_ble_gap_address_set() to make sure, that a bootloader running on the same device will not be cached on OS/X:
static const ble_gap_addr_t gap_addr...
This may be a newbie question, but it had puzzled me for a while now.
Looking at the PCA10031's schematics i can see two leds been used.
LD2 i can figure out. Datasheet...
MQTT Example in the IoT SDK compiles with size bigger than available 160KB Program space?!! Is this correct as I can't flash with the IoT SoftDevice on it.
The drive level of the nRF51822 is specified as 1µW, whereas the EPSON crystal suggested in the BOM for the EK boards PCA10000 and PCA10001 is specified for just 0.5µW (with...
hi nordic
i just got a little bit outdated "nRF51422-dk" package. I have problems with flashing
the boards pca10006 and pca10007- I tried to search for an solution, tried...
Hi all,
I'm an Android developer and I need to develop an application that detect when someone presses the button on Beacon and do something.
I've just bought these two...
I'm currently using ble_advdata_set to update the ble advert data packet. Before transmission I use the ble_radio_notification event . In this event for test purposes a single...
Hi,
I'm using a nRF51422+nRF6310 and I need to use SPI in order to connect with some devices. I am trying to run the example "spi_master_example_with_spi_slave" but I found...
