Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
It's been 14 months since the nRF 5x IoT SDK 0.9 was released.
Given Nordic's normal release cycle, that's an eternity!
Will there be another release or is it dead now...
Hello community,
Before I was using a pca10040 by Nordic evaluation board. The project, that i developed, is running well using the EB but when I change to sparkfun breakout...
Hello,
I'm working on nrf51822 with SDK9.0. I have two modules, one is working as a peripheral using s110 and another one is as a central using s130. Now central has a very...
Hi!
I am fairly new to programming micro controllers so apologies if I ask many questions.
I am using NRF52832. The situation is this - I have 2 devices and 1 host . After...
Hi all,
I've found the nRF52840 with USB but it seems a bit OTT for our application, something more like the 51822 would be nice, but cannot identify one, can anyone list...
Hello!
I have a code that is working perfectly on Eclipse for Linux and I would like to copy it to a windows computer with keil. I created a new project with Keil copying...
Hi, I'm developping endless PWM sequence.
That is ...
Only one output pin and the signal from it is repeated with the same period of pulse but with two different duty...
Greetings,
I'm having some trouble using the secure DFU bootloader and buttonless DFU service in my application. The code for both of these has been taken from their respective...
nRF52 SDK13 S132.
For example, I have handle from 0x180A service.
I want to read characteristic 0x2A24 from here.
How should do it?
In the watch window I can see event...
We are interfacing to a SPI Flash MX25R8035F.
When attempting to read 1 page of 256 bytes from the chip we break the read command up into 4 SPI Commands.
1) Read the Status...
Hi,
I`ve made fixes in SDK 13.0.0 files described below:
nrf_section.h : to supress gcc warning: invalid suffix on literal; C++11 requires a space between literal and...
When I set the PWM driver for very low frequency i can see how it blinks, the thing is that it always blinks where it's more or less 70% of the time ON and 30% OFF .
When...
Hello,
Working on a project using the pairing and bonding security model, I would like to filter out of a central's scan all already bonded peripheral devices. Or, I could...
For some reason I get a softreset instead of a sleepmode when I call sd_power_system_off();
Device: NRF52832
SDK: 12.2
S132 v 3.0
I do clear all gpiote interrupts...