Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello,
I am trying to control the smart phone function while making my device as HID keyboard, but It seems that the soft keyboard (smart phone on screen keyboard) clashing...
i think your nrf51 iot sdk don't have rpl functionality....
if i want to implement rpl on it what is the procedure...
if i want rpl on raspberry pi what is procedure......
i have bluetooth usb 4.0 dongle..which part of bluetooth stack it contains...?to support simultaneous master and slave connections will it need any firmware update...?
...
As we known we can set static passkey in peripheral side (s110) with the API sd_ble_opt_set(BLE_GAP_OPT_PASSKEY, &ble_opt) as below:
inline void setPassKey(void)
{
uint8_t...
I've tried all 4 versions of the HID Mouse Example provided through the Keil Pack Installer tool and can't seem to get any of them working.
The code compiles and downloads...
I was trying to compile the example code(nRF51 SDK8.0) for ANT and flash to my nRF51DK(pca10028) board, but the example code was not working on my board. I tried compiling...
Hello.
I'm now writing a software based on nrf51_sdk_v6_1_0/nrf51822/Board/nrf6310/s110/ble_app_hrs. The SoftDevice I'm using is s110_nrf51822_7.1.0_softdevice.hex. Why...
So I've been using a user submitted SD safe TWI implementation that I found here. This has worked well so far, but upon updating to SDK 8.0.0 parts have broken. Now when I...
Hi,
I'm using the NRF51DK which comes with the nFR51422. I initially flashed the board using the ble_uart example.
Since then I've tried flashing it with other examples...
Since we have some performance problems with sd110 V7.0.0, we tried a upgrade to v8.0.0.
This version(8.0.0) with IC revision 3 solved our performance problems:).
But a...
Hi,
I am working on a project regarding a portable device for healthcare monitoring. This device will have a nrf8001 module integrated that will communicate with a iOS...
Hello there,
I know that the range of the possible BLE communication depends on the internal configuration as well as on the external environmental conditions.
I would...
I downloaded the zip file from Git Hub Nordic.. and extracted it into C:\Keil_v5\ARM\Pack\NordicSemiconductor\nRF_Examples\7.1.0\ble_peripheral\
When I open the project...
Hi~
I have a nrf51822 EK board(PCA10001 V2.2.0), but the J-link OB can't flash 51822 chip.
The situation is:
1.I can see Segger J-link on segger software&nrfgo studio...
Hi all,
I've been trying to get a new Win 7 (x64) PC setup with with the Nordic dev tools.
Studio, MCP, SDK etc.
I've installed Studio (1.17.1) and MCP (3.7.1). This...
