Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi, I am trying to use your new sd 8.0.0 but there are a lot of compilation errors due to the new APIs and removed section from security structs in SDK 7.2.0.
Are we to sole...
Hello
I have the nRF51822EK PCA10001 (V1.0) and PCA10000 (V1.0).
I'm working on a project where i'm going to send data from a custom board over to the PCA10000 dongle...
Hi all,
I have a small question. If a GATT server needs to send data to a GATT client(about 65 bytes), does it have to create a service first and then adds characteristic...
i am trying to make connections between s130 device and end node which have heart rate service.
according to the s130 document once if you press the button 0 it will automatically...
Hi
during setup of a peripheral at startup, I need to add some wait periods in between steps of the setup. Is there some function like waitMS(int time) or something, that...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Folks,
Newbie here with mbed, using nRF51-DK, but old hand with nRF51822, S110, SDK, J-Link, Keil MDK, etc. Trying to figure out how the mbed SDK API maps down onto the...
I have 25Q64 SPI flash chip connected to SPI bus. Unfortunately it works too slow even with using IRQ routine via SPI0_TWI0_IRQHandler (everything done like in example spi_master...
I was wondering if its possible to do a "Create new user" function, so the new bonded devices are accepted only if the first connected master tells the peripheral to.
For...
Hello,
I have taken the ble_app_beacon example and added a few things... I am looking to do something very simple like light up an LED on connection. So i added the on_ble_evt...
When is the S130 going from alpha to beta or release?
I understand that what ever answer is subject to change...just hoping to get a "ball park" date/plan.
hello,
I recently purchased a NRF51 dongle and NRF51 DK. I was working with older version of NRF51 development kit. I did n't get any information in the user guide provided...
Hi,
I am using NRF51822 BLE. I wanted to know that when we put this BLE ic in sleep mode then, is there VDD_PA voltage is still 1.6V or it becomes shut off internally.??...
Is it possible to generate useful documentation from the provided .dox file ?
If I run doxygen.exe ble_api.dox I get some Latex and HTML output but looks incomplete because...
What would be the best way to go about sampling and transmitting a signal at 60 Hz? I am considering setting up notifications and a characteristic, but I don't think that...
