I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi, this question could be ridiculous question due to my lack of data structure knowledge.
As you see in the HID keyboard example (SDK 7.2), there are several buffers....
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
It took a bit to learn these offsets and configure the keil project for them. Do these need to change now that I want to begin using the OTA bootloader? I'm imagining that...
It's probably a rare bug, but it is still worth noting. I have been debugging this issue for a day.
I am using SDK 6.1 at the moment.
The problem was that Device manager...
Hello everyone, right now i make my own nrf51822 kit. it works good for all sample example when i use minimum current consumption example it shows 4.5uA current, then i erase...
I would like to create a sensor network consisting of up to 17 nodes, I've been collecting a lot of information about means of communication between them and a computer and...
Hi All,
From the data sheet nrf51822 have a aes hw modules which is used bt softdevice s110.
If i disable the pairing key .
Can I use the inbuilt aes module from...
I am using DEVICEID as an identifier (I know it's not necessarily unique) but when I break the two 32-bit numbers out into bytes, I am finding that the three most-significant...
Hi Nordic, I'm following a guide on this link hrm . I was testing the application with Master Control Panel 3.7.1 with my nRF Development Kit PCA10028. I looked up some of...
We all know we can send acknowledged data in Ant channel.
But based on my test. the acknowledgement message coming back to the originating device is just a dumb packet...
Hi,
I'm new to coding on this platform and i'm having issues. I have an ADXL335 acc sensor connected to P0.04, P0.05 and P0.06 of my NRF51822 (on a custom board). Please...
I cannot get uVision to recognize the J-Link OB device on my nRF51 Eval board. uVision DOES work with a different J-Link OB eval board targeting the same device, the Rigado...
Hi there
I was wondering if anyone has any information or a simple step by step guide for getting up and running on IAR with sdk 7.2 and IAR workbench?
Hi all,
I'm building an application for IOS & Red bear lab BLE shield and Arduino. The phone acts as a remote control for a toy car that I built . It works decently, but...
I'm having problems with a NRF51822 on a custom PCB. I've managed to get the SDK BLE samples working, HRS using Keil, JLink.
I was developing my solution with a MBED kit...
