Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hello.
I notice a problem with app_uart_flush function, which is calling app_fifo_flush function and in this we have a:
uint32_t app_fifo_flush(app_fifo_t * p_fifo)...
Is it possible to enter DFU / OTA from a DWT
i.e if the code crashes, and I can't trigger DFU mode by writing to a characteristic, can the WDT jump straight to the DFU...
I met this issue on some Android devices.
GATT connection is disconnected before before service discovery finished.
The issue is reporeted in following link.
github.com...
Hello, I'm using an android device to set cccd, it worked when I was running the project on nrf514xx @s110, it no longer does on nrf52840 S140, so now I wanna make sure the...
I have reformatted the code I had added earlier.
Following is the sequence of code
uart_debug_init();
gap_params_init();
services_init();
advertising_init();
conn_params_init...
NRF52832 S132 MPU6050 TWI
I want to finish the function:
When the ACC, GYRO data update, the INT pin to generate an interrupt, and then in the P026 pin configuration...
Hi,
I have the Nordic Thingy:52 (PCA20020 1.0.0 2017.19). It worked well until I downloaded new version of firmware 1.1.0 and updated Thingy. After that I didn't see advertising...
I want to use the UICR customer registers to store MAC/serialization information for my devices. It looks like the UICR customer section would be great, and the product spec...
I want to use whitelist in Central (nrf51822,SDK12),but I don't know which function to add the MAC address.
These three functions：
peer_list_get(pm_peer_id_t * p_peers...
Hi,
With S132 it is possible to advertise on specific channel.
See devzone.nordicsemi.com/.../
But, since from BLE5 advertisement can be done on any of the 40 channels...
Hardware: redbearlabs Nano V2 (see pinout below)
Programmer: DAPLink v1.5 supplied by redbear
IDE: Arduino with the redbearlab nano 2 board package
The schematic can...
I'm writing an Android application that connects to various BLE peripherals including the NRF51 and NRF52. I don't know if this question is appropriate for this site, but...
Hi,
we are trying to disable 2 of 3 advertising channels on nRF52832 SoC with the softdevice S132 (1.0.0-3.alpha) installed. The example project ble_app_beacon works well...
hi
I am using ESB_DPL protocol between 51822 and 24LE1, and i used the sdk 12.2 examples/proprietary_rf/esb_ptx.
In my case, 51822 sent some packages with PTX mode,...
