I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hi,
i am working on RTC to create custom clock to measure time it is working fine but when i initialise ble stack and softdevice and adverticeinit it is not working. and...
Hi,
Maybe someone can point me into the right direction, I'm on S110 and SDK10 for hardware/legacy reason.
I have a pstorage function using init, load, clear and write...
Hi.
I am investigating the cap touch for a while, and I am working directly with the capacitive driver from here.
As being said there and other places, the driver will...
Hi all
What is the minimum required length of a LOW pulse to be detected by the nRF52832 via GPIO SENSE mechanism? I couldn't find it in the product specification.
I...
Hi Nordic Team,
I am using board PCA10040 wtih nRF52832 SDK 11.
I have Added DFU code to ble_app_hrs_freertos example.
Once I will go for DFU from nrf Mobile Application...
Hi all
I was investigating a NMI_interrupt today and found out that it was caused by a race condition in the fstorage module.
The problem may occur after a flash operation...
HI ,
I am using nrf52832 with s132 . I am trying to measure ADC value at some periodic interval. In nrf_drv_timer_init() function , code gets restarting after executing nrf_timer_event_clear...
Hi,
I use bootloader from SDK6 and I have sd_power_system_off() in on_ble_evt in event BLE_GAP_EVT_TIMEOUT and BLE_GAP_EVT_DISCONNECTED. I use SDK7.1 and SD110 7.1.
It cause...
I'm programming an application that uses the NUS, and I'm trying to test my code using the Android version of nRF Connect. I'm using a nRF52832 on dev board PCA10040, and...
Hello,
With sdk13 and app_pwm library, I only got 9bits resolution for 32KHz freq.
The pwm should have 16bits resolution, with max freq 100KHz?
please could anyone...
hi ,all
I feel confused about" out_of_sync" and" in_sync" parameters .If a devece is in sync,how the channels was changed ?And what's the use of"nrf_gzll_set_device_channel_selection_policy...
we builded " BLE to IR " using nRF51822 , it was working fine with out the softdevice.
problem start when we integrated with the SoftDevice .
1.the problem that we need...
Hi.
I am trying to get a capacitive sensor library using a button ( 2 plates, one to ground, one to the AIN, separated).
It's going crazy, sometimes it just get tones...
hi,
I'm designing a board with nrf51822 chip. this board work on 2450 lithium rechargeable battery and it contain an MCP73831T circuit which is responsible of recharging...
Good Afternoon,
I hope someone can point me in the right direction.
We've customised an NRF51822 beacon and made it into a sensor but there seems to be an strange error...
