I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
I am working on a custom BLE service on the PCA10001. I can successfully detect and communicate with the PCA10001 using windows x64 MCP. I can also detect and communicate...
Dear Sirs
I am new with Nordic BLE Modules.
After successuful pairing with Windows 8.1 in a Tablet I need to get an active Service. For example I would like to obtain Battery...
We have an NRF51822 running S120 at 32MHz.
Our system has two removable batteries. If a battery is removed we need to switch to the other battery as fast as possible. We...
For TWI, SPI and UART is there a significant power savings from powering down the unit when not in use vs just disabling it?
Disabling the unit seems reasonable, but powering...
Hi!
I was trying to use nRFLoader to update firmware using example DFU Bootloader but app hangs on "Discovering" (after selecting device to update). What can be the reason...
Currently I can upload new application firmware smoothly (I use the dual bank setup). However, I have to use packets of size 20, so this takes a long time.
Is there actually...
hai ,
i am using the NRF51822 development kit. The NRF51 dongle i have used as a sniffer and a master control panel. Is it possible to load and run a s130 softdevice and...
Hi, I'm trying to estimate the nRF51422 current when running ANT. Does the softdevice use the RTC (LF oscillator) when in wait mode to save energy? Thanks
The Segger programing interface works. The virtual com port appears on my PC (COM5). The problem is that there is no board listed in the Motherboards section of the Device...
Hello,
currently I try to implement a GATT server on a nrf51422 with the s310 Softdevice. For testing I use the LightBlue IOS client on an ipad. I can see my GATT server...
I am creating an Apps which will give me a list of the running Apps in the background and foreground.
Hence Using XCode, I want to programmatically detect
List of Running...
I have a Arduino board and I want access to Ant Stack by UART. I flashed S210 in my nrf51422.
I try connect the Arduino RX/TX with TX/RX (P0.12 / P0.13), but none. Also...
Hi Nordic,
I'm wondering if I can use IAR Workbench to download SDK for nRF51DK rather than Keil. I want to develop a beacon that uses Bluetooth Smart. Can I do that in...
Hi,
Does the .hex file for V7.1.0 include the master boot record? I'm writing a JLink script to flash it and I'm trying to figure out, once converted to a binary file,...
I have the PCA 10028 Board. I would like to add a characteristic on an already existing service.
In the nAN-36 I see, what is necessary to set up service and characteristic...
