Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hello All,
I'm thinking a small plastic case for a portable device.
It is possible to place pcb board (with pcb antenna) above the battery (Li-Po) or can interfere with...
I want to log basic intermittent events and push them to a previously associated mobile device when one is nearby. The mobile device can then forward the events up to a server...
I'd like to know what is the minimum and maximum frequency I can generate on a GPIO with a 50% duty cycle (+/-10% at the worst case). Which resources should I use for that...
In my case active CE signal defines byte boundaries - for each byte individually.
From what I see, DMA seems to stop on rising edge of CS regardless what is declared in...
Hello everyone,
I'm using nRF51822 development kit to do BLE network experiment.
The boards I use are PCA10005 with omnidirectional antenna, and PCA10004 with PCB antenna...
I'm looking at the UICR hardware peripheral example , and trying to figure out the utility in writing to the UICR registers.
Why would I want to modify the compiled hex...
Very new, so please forgive the questions, but...
I have an nrf8001 that I've powered up. After initial power up, I'm able to read the DeviceStartedEvent but the response...
I'm looking to integrate a digital (PDM/I2S) MEMS microphone into my nRF51822-based design. I'd like some pointers to reference designs or other information -- the ones that...
Hi,
I would to know why when the DC/DC is enabled the current is very high (57mA) during RF sending.
Why at the end of RF sending the current is higher than...
I am modifying the bootloader. I am not using DFU or any of that, but rather copying a FW image over from external flash through SPI. The area of my code that gives me problems...
The documentation of the S110 contains sequence charts that explain how the different GATT operations are performed.
developer.nordicsemi.com/.../a00885.html
It seems...
Hi,
I've been trying to do fake non-connectable advertising with a nRF24LE1 with base on [1] and [2], they use nRF24L01+ with an AVR which I have ported to my device. I...
Hey,
I'm evaluating a nRF51-DK and face NRF_ERROR_INVALID_ADDR when trying to set a value in the local gatt server database.
My goal is to create a read-only characteristic...
Hi,
I'm using nRF51822 Beacon v1.1.0. Is it possible to detect that the beacon is being scanned? Is there any event generated during this process that I can catch?
