Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
E:\nordic\nRF5_SDK_12.2.0_f012efa3\examples\proprietary_rf\gzll\experimental\gzll_ack_payload
Use gzll_ack_payload this routine master-slave why always send and receive...
I'm using the experimental buttonless DFU app in SDK v13 to automatically change a device without buttons to run in DFU mode for an update.
I'd like to automatically reconnect...
hi:
i update app fail using serial ! SD version 8.0.2 . nrfjprog version 9.0.0.
the device page as follow:
APP_START: 0x18000
APP_SIZE: 0x18000
SD_START: 0x1000...
I use SDK9 s130 nRF51 in central mode. When I save 2 devices in my central, all ok.
In a
m_peer_table[index].id_bitmap
i see that value 0xFF changed to 0XFC
But...
I have been following BLE Services, a beginner's tutorial to add a service to my ble_app_template project. But tutorial was written for SDK 11 and I'm using SDK 12 (s130 &...
Hi, i am using this program to send the data captured on 3 sensors from AIN0,1,2 to the mobile nrf toolbox application via BLE UART.
The problem is that when the sampling...
Hi,
I had done OTA DFU update on nrf51 DK Board using SDK11 version.
Now i wish to do same thing with other custom board which is having nrf51822QFAA. For that, my hardware...
How to test Link loss in the proximity profile using Andriod phone.
By using 'nRF connect' andriod app,Here we can only write and read the Link loss Alert Level.By setting...
Hello,
I just went through the release-notes of the S132 and found a passage that the s132_nrf52_4.0.0-1.alpha introduced some new ble-features like f.ex. the role-configuration...
Hi!
I'd like to collect statistics from BLE physical layer, namely about errors that have occurred in receiving packets on a BLE advertisement channel. I see from custom...
Hello, I working on nRF52DK, for programming am using Eclipse IDE. For that I am following nordic tutorials here
I need to add a new project it does't have any makefile...
Hello dear Engineers!
the questions are should I connect pins DEC2:A18 and DEC2:E24 externally ?
shuold I use Capacitors to decouple both these pins (in Reference no...
Dear developers,
we are considering purchase of a reliable programmer capable to flash the nRF51822 in production, one possible option is the SEGEGR FLASHER PORTABLE or...
Hi!
I have noticed strange problem with one of GPIOs - P0.15. We have tested 50 devices based on nRF52832 and 3 of them have problem with P0.15 after few days.
P0.15...
The default I2C address of my sensor is 0x29 (7-bit).
If the least significant bit is low (0x52) the message is a master write to the slave. If the lsb is set (0x53) then...
