I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Is the GPIO pull down/up asserted on the 'inside' of the input disconnect switch or at the input/output pad? The diagrams would indicated that it is on the 'inside' of the...
This is function definition:
static uint32_t battery_level_char_add(ble_bas_t * p_bas, const ble_bas_init_t * p_bas_init)
This is declaration of the automatic variable...
Before starting advertising, we want to write some configuration information to NVM. In order to write to NVM, we first call sd_flash_page_erase and wait for the response...
I just posted a package of simple tools I wrote for OSX over on Sourceforge . The main app is a Cocoa app which lets you choose code, softdevice and bootloader (last two optional...
I Saw iBeacon Packet in the website
(d6 be 89 8e) Access Address for Advertising
(40 24) Header
(05 a2 17 6e 3d 71) Mac address
(02 01 1a 1a ff 4c 00 02 15 e2 c5 6d...
I want my peripheral device to act as a beacon while it is in a connected state with a master device. Is it possible to start not-connectable advertising in parallel with...
I am working on a nrf51822 UART bootloader using Keil 5.14 (though I had the same problem with 5.1). If I start with the pack example dfu_dual_bank_serial_s110_pca10028 with...
What happened to NRF_FICR_Type.INFO and FICR_INFO_Type in nrf51.h?
This was in ./components/drivers_nrf/hal/nrf51.h in nRF51_SDK_7.1.0_372d17a
but is missing from ....
Using the nRF51422 with the TWI hardware version. Just playing around to verify signals with the following code which just configures the TWI1 and then repeats continuously...
Hi,
i tried to update the firmware of nRF51-DK but it crashed and now Keil uVision says "Cannot find the JLink version number"
Its also not showing in the nRFgo stu...
I'm developing application using your devices (PCA10001/PCA10000) and S130 SoftDevice. I tried to implement DFU/OTA feature in my app. For this purpose I used DFU sources...
Hi All,
Does anybody has a working setup using SD 7.1.0 with SDK 7.2.0, iOS 8, DFU with a secure connection?
When I use no encryption it works, but when I enable encryption...
So I'm currently trying my hand at some very simple things that one can do with the NRF51-DK.
One of those things involves sending notifications to a client on certain...
Hello,
I'm testing n51822 with low voltage mode, and want to check the BOR condition.
Is there any threshold for brown-out reset, or voltage tolerance? e.g. 1.68V...
Hi.
I have received down the source of the example of experimental_ble_app_uart in my keil.
I use register.(NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;)
but, Hardfault occurs...
