after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I've using mynewt to develop an application using the nRF52 DK (PCA10040 1.2.1, IC marking: N52832 QFAAB0 1701FH). I've been using their basic hello world application...
Hi,
I would like to update advertising packet, but every time I get error NRF_ERROR_INVALID_STATE in function sd_ble_gap_adv_set_configure(). I set all parameters properly...
Hi,
I am connecting the nRF52832 UART (on my nRF52 DK) to an external device, which by default uses 9600 baud rate (but can be reconfigured differently).
In the case...
I have a board populated with the nRF51822 and associated components for the application.
I am able to flash the device successfully and successfully verify the flash. ...
I want to send data from the device to the server in some way.
We plan to connect the device and Android via Bluetooth and connect to the network using Android's 4G line...
Hi
We measured the SPIS waveform and found some issue on tspis, vso.
In nRF52832 v1.4 page 303, the max value of tspis, vso is 19ns but we measured it is around 39ns~49ns...
Hi everyone,
First of all ,Thanks for being such a supportive forum, I ask a lot of questions(I am a beginner to nordic and BLE)
I am using the example given in the sdk...
I am using nRF52832 IC with SDK v15.
I want to sample some data with 3200Hz sampling rate from SPI interface. There is an accelerometer connected via SPI interface. I...
We use nRF52832-QFAA-B0 and we found that PAN16 issue is still present, at least in some corner cases.
It happens when we put the chip in low-power mode with WFI ; at wakeup...
Can anyone help me?
Each service is working standalone.
There are two cases:
1.the BLE can't connect auto by iphone.
2.firmware can't receive notify...
I am hoping there is a Wiegand protocol file i can import into the project so i dont have to write it. Is there a function that has already been done i can import into my...
Hi Everyone
I was trying to get the BLE Uart working with the nrf52840.
Everything works fine, all files are compiling and running, but when i debug the code using segger...
Hi,
I use the peripheral ble_app_uart with nRF52832 (Murata module). The nRF52832 is connected to another MCU, STM32L476, via UART.
P0.5 - RTS
P0.6 - TX
P0.7 - CTS...
Hi.
I am developing a FW for nrf52832 and am using the nrf51 dongle as a testing tool using nrfconnect.
However, this is not working good because the dongle misses notification...
i need use flashwrite in my code, but i found sometims when i write data in flash, the BLE connecting sometimes is borken, i used this funciton flash_word_write(uint32_t ...
