Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Hi,
I followed the instructions for importing the Thing:52 firmware into SES and managed to get the firmware compiled and loading, and the code reaches the main function...
Hi,
I'm following DFU quick start guide and I'm using mesh SDK v2.0.1, I have a problem in step 4 wheere I need to generate a hex version of device page, I did this :
...
Hello,
Are there any conditions where the sd_ble_gap_disconnect() will not immediately terminate the link?
My Setup: Nrf52, SDK 13.0.0, own board, based from HRM code...
Hi!
I want to start scan in central mode after one connect has established and I received success evt PM_EVT_CONN_SEC_SUCCEEDED:
In a SDK13 I can make same, but at SDK15...
Hello!
On the firmware for a certain product, we are using the scheduler module to manage the access to the peripherals (SPI, TWI, Timer, ...), and have also enabled its...
I implemented manufacturer specific advertising to transmit important data without having to connect to the ble peripheral. These data can change over time so I need to be...
I measured the power consumption on NRF52840 DK with project peripheral blinky (SDK15.0.0). The average current is 704uA and the base current is 680uA when connecting to another...
I have a test suite connecting to a nRF52832dk using RTT. This one test writes random data to the UICR config area, resets the chip, then reads back the config.
When running...
Hell ,
I am planing to use nRF52810 for one of my mesh application,now query is
How much power consumption its will take when RF is disable and listening only external...
I am about to buy 5 pcs of nRF52840 DK Development kit for nRF52840 SoC to use for Long Range. How can I ensure the development kits are mounted with chip revision C or later...
Hi Team,
I have read in nordic documents that BLE 5.0 will have 1.4 Mbps of through put.
But when i am testing the through put example with my nrf52832 board, i am only...
Hello. I'm using the example of the light_switch_server project. I need to configure a server (light bulb) driven by 3 clients (buttons), how can I do? I tried this way, but...
Hello Nordic,
I have to transmit data from the nRF Chip(now i'm testing nRF52832 DK Board) to a PC on UART serial.
Each beacon has transmitted advertising and scanRSP...
Based on the nRF24L01P Product Specification 1.0, after 24L01+ enters into Standby-II state, the only 2 ways to leave this state are 1, set PWR_UP to 0, 2; 2, Feed data into...
