Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
when i upload the hex file of a s132 softdevice example program through nRFgo studio,
its shows hex file uploading failed and shows this message "Invalid SoftDevice, data...
Hello Everyone,
I am facing an issue when trying to connect back BLE central again after disconnecting it from the BLE peripheral once.
The issue is reproducible as follows...
If I want to send two byte, how can I do? I use the https://github.com/NordicSemiconductor/Android-nRF-Blinky sample code.
In BlinkyManage.jave
public void send(final...
hi All!
I'm trying to use new SD140-6 function sd_ble_gap_adv_set_configure() , according to spec. if last PARAM is NULL, function behavior : " When this function is used...
Hello, there was a strange problem in the mass production of my product. The previous batch of problems was less, about 0.5%. The later batch is quite serious, 45 of 500 products...
Hej,
on trying to update firmware on nrf52832 over the air I'm getting the error message INSUFFICIENT_RESOURCES.
Actually I don't understand the error message because...
I want to put the BLE program to the firmware of another STM chip and load the program via the I2C to the nrf52832. Will it work? If yes, is there any tutorial or example...
Hello,
I'm using nRF5 SDK with version 15 and nRF52832 IC. I want to sample some data with 3200Hz sampling rate. I can set the timer minimum 1ms Which means 1000Hz. How...
I want to write at the end of memory ROM data in address 0x7FFFF
uint8_t tst_arr[1] = {6};
sd_flash_write((uint32_t*)0x7FFFF, (uint32_t*) &tst_arr, 1);
Is it correct...
Hello ,
System configuration
Set up 1 Adafruit BLE Feather running stock central UART example from NORDIC SDK version 15.0`examples connected to host PC using USB
Set...
The dedicated NFC pins on the nRF52840 are P0.09 and P0.10. However, these are noted as "Standard drive, low frequency I/O only " pins, with "l ow frequency I/O" defined as...
Hi, I'm facing an issue after provisioning the Client and Servers from Light Switch example of Mesh SDK 2.0.1, using the Android App. Provisioning is successful, however,...
Hello,
Following on from this question , I've been trying to identify the source of unexpectedly high power consumption when using the RTC. In order to test this, I am using...
Hey all, I am using an NRF52 DK and am trying to combine the 'pwm' and 'ant broadcast' examples. Both examples compile fine on their own, but when I try to combine I am getting...
I have a number of (probably naive) questions regarding the internal temperature module on the nrf52832.
1) Regarding the FICR values for temperature. Are these programmed...
