Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Hi Devzone:
I am researching how to maximize radio performance and stumbled on a statement on page 356 in the spec:
"Typical sensitivity applies when ADDR0 is used for...
Hi! Currently I have a nrf52840 devkit hooked up to an SD-card for storage through FATFS (using SPI). I would like to add a BME680 environment-sensor to the board and have...
1. I am trying to connect one node (say node A) from two android phones say phone A and phone B. The node A is configured as an on-off server for lamp 1, but it could not...
Hi
I am working on a project which needs to be developed on FreeRTOS, I am facing an issue i need logs at backend using RTT as my both serial_uarte are being used for communication...
Hi Community,
I am trying to program a timer to get a clean timebase of 50ms. But for some reason
A) the timer is little slower as expected. I have to add few counts to...
hi，i want to control a led driver by frequency send iic data, i need send 600 bytles once at least 10ms each time ,and the 600 bytles send by 3times.send the 600 bytles need...
Hello, how can I increase LOG backend queue size? I was comparing some sdk_config settings with some examples, but did not find difference and the example does not fire this...
Hi,
I am trying to capture a modem trace to send to Nordic for analysis, however Nordic says they are unable to open the ones I've captured so far. I am using the NRF9160...
Hello,
We are upgrading a nrf52832 project which is based on SDK 14, soft device 5. Currently we depend on dual bank DFU operation but our application. Unfortunately we...
Currently working on flashing the bike power tx example to my Arduino Nano 33 which uses a NINA-B306 nRF52840. The device is wiped clean with only the s340 softdevice loaded...
I am trying to run one of the examples in the SDK (...\nRF5_SDK_11.0.0_89a8197\examples\peripheral\blinky\pca10028\s130\arm4) with the name "blinky_s130_pca10028" but its...
Hi, I am starting to developing applications for the nRF5340. I am interested in exploiting the added functionality that Bluetooth 5.2 provides. I want to use a smartphone...
Hi,
We have an unusual problem involving FPU interrupt clearing and battery charge state on the NRF52832.
We are applying the following fix to reduce power consumption...
I am really struggling with getting started with software development of the nrf52840. I have looked at the SDK but I don't understand where I can find what SoftDevice I need...
