As title.
In nRF54L15 DK, I set "SB_CONFIG_BOOTLOADER_MCUBOOT=y" in file "sysbuild.conf".
It makes main function GPIO toggle stop.
Do have any solution to prevent...
Hello Nordic team,
I am testing a plain CoAP telemetry upload from an nRF54L15 DK over Thread using a Raspberry Pi OTBR and NAT64 to ThingsBoard Cloud.
Hardware / software...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hi,
We have deployed some devices now, and we see quite some modem faults popping up.
Could you try to give all info on what you know about these faults we have from...
Environment
SoC: nRF54LM20 (DK; silicon reports nRF54LM20B ENGB — also reproduces built for the LM20A target)
nRF Connect SDK: v3.3.0-rc2, west v1.5.0
Bluetooth: SoftDevice...
Hi all,
I am working on CAN driver for the MCP25625 device, which communicates to the nrf9160 via SPI. I am following the SPI example https://github.com/Rallare/fw-nrfconnect...
Hi，
in the timeout_handler of app_timer_create, invoking function nrf_esb_write_payload(&tx_payload)，The timeout_handler function won't come in again，why? timer cancel?
Dear all,
I am using NRF52832 for a mesh application. I utilize the light switch example for the project.
Description of my application:
1. We have 6 devices. They...
I am trying to integrate LPS22hb sensor n nrf52832. I am starting with twi_master_using_nrf_twi_mngr example(sdk15a->compents->drivers_ext->lps22hb)
I have added lps22hb...
Hello,
I have a device that samples data from a bunch of sensors every n hours, and that when in IDLE must consume around 100uA. To achieve this, I'm using a counter (that...
Hi,
I connected MCUBoot and FOTA to my project. I checked that the download is working, but not stable. I saw in the documentation that you can enable the continuation of...
Hello I need a falling edge response via GPIOTE. The settings I use for sdk 16 to sdk 14.2.0 do not work. For sdk 16 I use the functions nrfx_gpiote _..., for sdk 14.2.0 nrf_drv_gpiote_...
I observed a peak of 334 ua during system-on low-power mode during idle time which is periodic around 4 sec. I am using ble with RC clock option.
1.is it waking for calibration...
Previously, I learned that BLE is capable of 1:1, 1:N, and N:N communication, but I didn't get the exact information. Can I get some information? How do you do it, what's...
What is the max current nRF52840-DK source from Vdd pins, i am connecting multiple sensors through the Vdd of nRF52840-DK i want to know how much load it can source ?
Hello,
There is a problem printing the log message. I am using SDK12.3, keil compiler and segger J-Link. After modifying the project a little, normal log output is not available...
Does the nRF9160 have an ATEX component certificate? Why there is no marking such as "Ex ia IIC Ga" provided? What exactly do you understand by the term "ATEX compliance"...
After a conversation with a Nordic engineer and some research it looks like there is no official way to upgrade a product over the air from an nRF5 SDK based product to an...
I ported the Thread Secure DFU example to use FreeRTOS, however I get a hard fault if something is scheduled using the app_timer provided.
Calling coap_dfu_trigger or handling...
