I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
What exactly are the "glitch" issues with the PWM master library ? I see there have been some recent updates, but no clear indication as to what issues remain or have been...
Hi,
How to upload and debug application program to the beacon with S110_nRF51822_7.1.0 and bootloader (DFU) using J-LINK? The standard procedure takes into account OTA...
Hello,
I want to detect the advertising data of more then one Beacon with the SDK51 and read the TX_Power for a location-application.
I´m inexperienced in stuff like...
will gazell device fall-back immediately to out-of-sync state upon reaching the max tx attempts even if the sync counter is still less than the set sync lifetime?
thank...
I got a nRF51822 based module and I loaded a slightly modified application based on "ble_app_beacon" example in nRF51 SDK via SWD interface using J-Link. The code has been...
Hello,
I have an application in which a BLE peripheral device will be essentially permanently paired with a client. The client will need to connect infrequently with the...
Hi,
I am trying DFU example on nordic evaluation kit using example on github:
github.com/.../DFU-Bootloader-for-nRF51-Evaluation-Kit
However, while compiling in keil...
SDK 7.2
S130 Alpha 0.9
I'm using the UICR customer register address 0x10001080 to stare a single 32 bit number. The code below is a bit of "brute force" to demonstrate...
Hi
I'm trying to make a new S110 BLE project for my nRF51 DK from "scratch" in Keil 5.14 (New uVision Project -> nRF51422_xxAC) , but every time i try to build the solution...
when I program wechat ble demo to my nrf51422 boards with S310 softdevice in Keil, return error like this "No Algorithm found for: 00000000H - 00007503H; Programming skipped...
Looking in the Keil Packs Installer, there are over a dozen entries for NordicSemiconductor::nRF... - each with its own version number.
So which one actually represents...
Hello
I'm trying to implement a number of different interrupts using the nRF51 DK but I'm having trouble understanding how to use the GPIOTE_IRQHandler function.
Basically...
Hello,
I read a while in this forum and found out it might be a little tricky to get I2C working when using a Softdevice. Is that information still valid or outdated? ...
I 'm using SOFTDEVICE.
Can I choose the BLE and NON_BLE while the applications running?
I want to implement, as below.
When I want to use bluetooth, BLE is run. and...
For a school project we have to develop a beacon system, to easy use different beacons we want to be able to change the major and minor from the beacons with UART communication...
