Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
hi Ole Morten:
thank you for your great support.
i have tested nrf6310\temperature_example. at 30(Celsius)
I checked the data. NRF_TEMP=0x000002AF; TEMP=0xFFFFFFAC;...
Hi,
I need help on calculating the current consumption of our device when it is in advertise mode. So please answer the below questions.
What are all the significant...
Hello,
i would like to use HRM, HID, BAS and DIS profiles simultaniously. I used HID mouse example. I append required HRM things and it work almost properly. Problem is fault...
Hi, I'm a beginner. I want to add to example of the proximity, next service identical to battery service. I need to send 1 byte of data.
Everything works well until when...
I have an application that reads an nRF51822 pin configured as analog input and then sends that value using "ble uart" (included in Nordic's sdk). Analog input is read in...
Been studying the S110 5.x -> 6.0 migration docs. Are there any project-specifics / include-paths / Keil build-settings that must be updated as well?
Do I understand it...
Im stuck that i can't get my Motherboards to update. Just goes into an endless loop of saying toggle power to rest it, starting boo loader, Couldn't start.. etc etc..
Attached...
I have a nRF51822 device which has softdevice and bootloader.
And I'm trying upload my app with following steps:
make .bin file with gcc
Push the DFU button, and...
I'm running a custom nrf8001 board and the nrf8001 is consuming approx 6.2mA on it's own in advertisement mode using the uart demo. Has anyone had this same problem? Any advice...
Flash write and erase works fine, if ble is not initialized( ble_stack_init()).
Once ble is initialized, any write to NRF_NVMC->CONFIG hangs the system.
Do I need to...
Hello!
We are using a custom hardware design based on nRF51822. Recently we switched to the new chip version QFAAG0 with softdevice 6.0.0.
Our application needs a repeating...
I have tried HTS(Health Thremometer Service) sample Program on nRF6310, PCA10006, SEGGER J-Link Lite and iPhone5C.
First time, temperature is displayed on the iPhone5C...
Hi,
I have a custom board with nRF51822 chip on it and tried to run the proximity sample program on it. I have used the nRF51822 develpment board + nRFgo Motherboard to...
