I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I try to send NRF_DFU_OP_PING reqeust ,then received BLE_GATTC_EVT_WRITE_RSP message. but write_rsp.len is equal to 0,.I can see gatt_status is BLE_GATT_STATUS_SUCCESS. I...
hai ,
i my application i should connect 5 more peripherals with one central .
at first i connected with peripherals mac id , mac id hard coded in central
in central...
Hi,
Is it possible to be notified when the device is entering/exiting idle? All I can see is that idle thread calling k_cpu_idle which doesn't appear to have any hooks?...
Hi! Some prerequisite info:
We are using nrf52840 boards as our peripherals
We are using v16.0.0 SDK
We are using the s113 SoftDevice, more specifically s113_nrf52_7...
I want to connect and get data multiple peripheral to a single central device.
I used this example https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
...
I can't figure out how to respond to a custom Zigbee cluster command, let alone send a custom response. Is there any example on which I could understand how to send a command...
Hi!
we're just finishing the layout for a custom nRF52832 board. On the custom board we have a connector for SWDIO and SWCLK to flash the firmware. Can we use theese 2 pins...
Hi,
I'm trying to familiarise myself with the available crypto functionality on the 52811 and have managed to get basic AES-128 block encryption working using the ECB peripheral...
Hi,
I am using pc-ble-driver-4.1.1 to receive BLE peripheral Device 240 Bytes notifications. And I used "pc-ble-driver-4.1.1\examples\heart_rate_collector" as starting point...
Hi Nordic team,
we want to connect 2 nRF52840 based modules with Coded Phy S=8 Mode to make an cable replacement (NUS). MTU Size is 244 Byte ,to transmit cyclic 200 Byte...
I am trying to connect the DK to AWS.
I got the AT example working and uploaded the certificates. I managed to update the prj.conf file (and then took quite some time to...
It continue to give "No device available" when I connected thingy 91 to the nerf connect programmer app. I tried turning on device while keeping SW3 pushed but still not detected...
