Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hello,
I am trying to connect NRF52832 with another Bluetooth module using custom characteristics. I was able to connect two NRF52832 modules but I can't connect to another...
Hi,
After updating NCS folder to latest Master branch, SES4.52 is not able enter into debug mode.
Receiving error as: failed to set startup compilation break point:...
I have a bootloader, softdevice and firmware (all with sdk 15.0 and softdevice V. 6) on a nrf 52840 on an counter-pcb.
I have upgraded the firmware to sdk 16.1 and use the...
Hello together, I am just starting to work with the nRF9160 and have some problems with the configuration. I inserted the iBasis SIM card and tried to get a LTE connection...
Hi,
I am using a ble_app_blinky example (SDK16) to communicate with the BLE devices. NRF52840 is connected with the client devices and successfully sending the data to the...
Hello,
I would like to know if it is possible to not use softdevice because i need more flash for my code. I guess it is possible but when i don't enable softdevice in my...
Hello,
i'm trying to use SPI with nrf9160DK as master and RFM96 module as slave. At the moment, i'm developing elementary functions to write and read from my slave device...
Hello
I am working on Nordic nrf52832
I am using the "ble_app_blinky_c_pca10040_s132"
I want to use ble for scanning a beacon (eddystone TLM) and collect its data. ...
please help. I need functional description of what is need step by step for doing a zigbee hardware device switch and management over bluetooth on the thingy52, i have all...
Hi Team,
We are using the NRF52840 with s140 Soft device for our BLE application.
While we are facing some issues while doing debugging.
1. We are getting Hard Fault...
Are there any issues of pairing a nRF52833 using OOB pairing with a IOS device? Is there a good example code I could start with?
Thank you very much.
All the best
P...
The system requirements: 50 identical nRF53-based devices (each with a sensor and an actuator), positioned within a 3x3 meter square should be connected to a single computer...
Edit : The code posted below works on the 96x96 3V(LS013B4DN04) variant of the display, I still have no idea why it doesn't work on LS044Q7DH01, but I'm guessing it doesnt...
Hello!
I have some devices with a custom built PCB on my desk, all of which have my own custom firmware on it.
Sadly the devices don't have access to the debug pins...
Hi Team,
May I know the functionality of the below mentioned signals:
MIPI RFFE interface pins: VIO, SCLK, SDATA. MAGPIO interface pins: MAGPIO0, MAGPIO1, MAGPIO2. ...
