Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi Nordic,
We are working on Android and iOS apps. Currently using S3 with Android 4.3 and Note to communicate with nRF51822. Baud rate of 19200bps for our serial communication...
Hello,
Is it possible to increase the accuracy of the advertise interval? Im attaching an oscilloscope screenshot showing the S110 device advertising with a 20ms interval...
Hey All,
I am working on a board that is based on the nrf51422. The system goes to sleep and gets woken by an interrupt. One of the programmers claims to have managed sleep...
We use nRF51822 with S110 as a peripheral connected to iPhone master and looking for RSSI.
RSSI with correct value is received by the peripheral application every about 1...
Are there any sample applications that use a joystick press as an interrupt instead of a button press? The dev board I'm using uses the nRF6350 display and I was wondering...
Hi
I used the example from nrf51822_v4.4.1.31827\Board\nrf6310\spi_master_example for my PCA10001 board, as I know the pins configured in this example are for nrf6310 board...
Does anyone know how to implement a wrist watch LCD display? I mean a bare LCD Display, without a pre-build driver (I2C). Can I do it directly or I need another IC to drive...
Does anyone have any solid numbers on the maximum throughput achievable on
the nRF51822 USB dongle that comes with the nRF51822 Eval Kit?
Application - OTA protocol Gazell...
Dear Support Team,
currently I'm working on a custom board which contains the NRF51822_QFAB_A0.
I installed the softdevice (not the most recent version, but a version...
Hi,
I have bought nRF Beacon Kit, and I have downloaded "nRF Beacon Android 4.3.zip", but I can't find nRF Beacon Service source code.
Where is it? Please tell me.
...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
it register a handler, what about restart and run pstorage_register again, how it insure everytime we get the same address for our content in the flash?
before pstorage_register...
I'd like to measure the voltage of a lithium ion battery every minute or so in a way that's highly accurate. I need to do this without using the Soft Device because a) I need...
