Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I've configured UART2 on the nRF9160 to connect to a nRF52840. The nRF52840 generates a payload and sends it over to the nRF91. The payload size during testing was 65 bytes...
Hello,
I am developing using nrf2840 PDK, SDK v17.0.0, S140
I have made two services, one is to control the led blinking rate via nrf connect android app and the other...
Hi,
Is it possible to have dual transport for DFU (UART and OTA)?
I read this in the forum: https://devzone.nordicsemi.com/f/nordic-q-a/28118/multiple-dfu-transports ...
I have nRF52840 as the central and nRF52832 as the devices. I have the device names as TELCO_456, TELCO_457, TELCO_458 in the connectable advertisement packet. I have disabled...
I am trying to capture sniffer logs for a custom BLE peripheral using nRF51 dongle and Wireshark. I am following this guide here to install the Sniffer tool in Wireshark....
>I will start by prefacing that I'm not by any means an engineer and my only knowledge with BLE/embedded systems comes from curiosity, side projects and trial/error<
Story...
Hi,
I'm running of the fw-nrfconnect-nrf master branch (commit: 96e75dba598320c2707dede3ffef44bf326a89e3) because there are some improvements since the release of SDK v1...
Hi,
I am developing a custom device with nrf52840 and use SPI for flash driver and radar sensor.
For better SPI performance of the flash driver and radar sensor, I am...
As an example of this routine：
D:\Project\nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_hids_mouse\pca10040\s132\arm5_no_packs\ble_app_hids_mouse_pca10040_s132...
DK is not powering ON suddenly.
All the Power Switches are selecting properly (SW8 = ON, nRF Power source = VDD, SW6 = nRF ONLY)
USB is connected to J2 Connector.
Observations...
Has anyone been able to connect the nRF52 to MATLAB using their new Bluetooth Low Energy Communication interface ( https://www.mathworks.com/help/matlab/bluetooth-low-energy...
Why is "No location data available" always printed when SUPL data is downloaded in gps sample app? This happens at any place. I guess this causes a long TTFF.
This is a...
Hello. I have a DK nRF9160 0.8.2 version. I am sending AT command through UART with an external MCU (STM). I am interested on evaluating power consumption during an UDP packet...
Hello,
I am trying to integrate OPTIGA Trust X with the OpenThread example, "mqttsn_sleepy_subscriber"(from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0 SDK). I tried adding...
Hello.
I am running Segger studio 4.5 on Windows 10 and the ble_app_uart example project that works fine with one connected central device (i.e. iPhone with nRF Toolbox...
