Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hello,
I have a gateway project where I need to receive data from BLE and send on ANT network. As a first step, I took the NUS or ble_app_uart and changed the softdevice...
Dear Members,
I saw ST7735_DC_PIN and ST7735_SS_PIN, which one should I connect to my LCD it has only CS pin ?
ON LCD board ST7735_SCK_PIN 47 --> P1.15 PIN 3 SCK ST7735_MOSI_PIN...
Hello Everyone,
I am using nrf52 dk development board. I'm having a problem when I load my ble_app_uart example . I am getting an error message Error: Flash Download failed...
Hi,
I'm trying to use the nrf52832 as the SPI master to get read/write flash ic MX25L6433FM2I-08G(address - 0x00 to 0xFF).
In loopback case got data but when interfacing...
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
I get started with Zigbee Door Lock Example in https://infocenter.nordicsemi.com/topic/sdk_tz_v4.1.0/zigbee_multi_dynamic_door_lock_nus_example...
Hi,
We have ordered nr51822 chips in the past. Recently, we made a new purchase and on programming we have discovered that the FICR register information is different for...
Hi Folks,
I am currently implementing a power down routine onto the nRF52840 SoC and I have some questions regarding the right way to configure to system On sleep mode...
Hi,
Is there an example code which can be used to evaluate libuarte while softdevice enabled? I have tried the individual examples in "nRF5_SDK_17.0.2\examples\peripheral...
Hello,
I would like to know what exactly is doing PM_HANDLER_SEC_DELAY_MS and how can affect to the interoperability.
I saw in the bms example (sdk 15.2) it is set to...
The BLE specification says that the CTE can be a maximum of 160us long. I am trying to set CTE length to 160us, but every time i try to do so, firstly the transmitter stops...
Hi Devzone:
We are using J-link pro to collect trace data from nRF52833 DK board, and we found a rather strange behavior:
The sw interrupts would end on its own without...
Hi,
I'm trying to connect an NRF52840-DK to a MAX30101 Wing board via I2C/TWI. I've set up the TWI Manager to send a message asking the MAX board for its part ID.
This...
nRF5340 with NCS 1.4.0.
I'm using the NUS (code derived from central_uart & peripheral_uart sample) and i'm trying to send longer frame.
I have tried to add the following...
Hello,
I was trying to recreate the blinky program for the nrf52840dk using the nRF5sdk using Segger embedded studio.
I tried doing it by opening the blinky example code...
