after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I've been working on the SPI module for the nRF51822. I used the sample spi .c file as a starting point, but I got rid of the timeout (not sure why there is a timeout...
Hi,
We have nrf51822 evaluation kit and some custom board with nrf51822 chipset(works fine). And also we have tested the nrftoolbox application with the proximity service...
I use the example "Keil\ARM\Device\Nordic\nrf51822\Board\pca10001\led_radio_example" and "Keil\ARM\Device\Nordic\nrf51822\Board\pca10000\led_radio_example" to communicates...
Hello, I think there's a mistake in page 35 of the specification, it says that if Auto Retransmit is disabled (that meaning Auto Retransmit Count = 0 in SETUP_RETR register...
Hi all,
I am using an nRF51822 Development Kit and I would like to create a simple test code that allows me to send data (no matter what kind of data, also a sequence of...
Hello, I am working with both QFABA0 devices as well as a QFAAC0. Because of the outdated silicon I am constrained to SDK V4.x and SD V5.x
My current test setup is
I...
Hello,
which profiles are available currently to the S120 protocol stack? In the nRF518 SDK V5.1.0 I could find only one example profile for Heart Rate. However, this is...
HI,
I am the beginner of develop bluetooth le device, and test the sdk 4.x examples and it's work correctly,
then i updated the sdk to 5 , but i can't get the example...
Hello,
I am Ethera's engineer, evaluation technologies to include on our next generation products.
Here our goal is to have a transparent mode between a smartphone program...
Hi There,
I want the functionality of my device to change when a value is written to a gatt characteristic. I've written an event handler that gets called whenever a write...
Hi,
I have Keil 5.1, SDK 4.4.2, SD 5.2.1, PCA10001 from EK v2.0.0 and I am trying to make SPI example from nRF6310 work.
I have changed below lines as:
#define ERROR_PIN_SPI0...
Hello,
I'm using a nRF51822 CEAAB0, SDK 5.0.0 and S110 6.0.0-5.beta to make an Apple ANCS client and for now I'm trying the ble_app_ancs example. I read that CEEAB0 arent...
Hi all,
I use nRF51822, sdk_v5_0_0_34603 and s110_nrf51822_6.0.0-5.beta.
In a different periods of time appears error "0xDEADBEEF, 722, src \ ll_adv.c".
Error appears...
hi,
According to nRF51_reference_manual doc and Relate Discuss.
I think that power mode have system on(run/idle) and system off and
at system on idle(sleep) mode which...
