I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi, I want to send Door Lock Event Notification commands.
so I modified ZB_ZCL_DOOR_LOCK_SEND_LOCK_DOOR_RES macro in zb_zcl_door_lock.h file.
The result...
hello,
i added scan_rsp_data to add a name on my beacon, but now i cant see manufacturer data on the ble_gap_evt_adv_report_t structure but i can see that perfectly on my...
I'm seeing the modulated output of %XRFTEST offset by approx. 1.675 MHz from the set frequency. Modem version is v1.2.2
Here's my command:
AT%XRFTEST=1,1,1,19500,23...
Hi!
Looking at the schematics for the nRF52833 reference circuitry I see that when USB is used, the VBUS is connected to the C18 capacitor, then GND, and if USB isn't...
I have programmed my device with ble_app_rscs available on nRF5_SDK_15.3.0_59ac345. I was expecting it the main loop
the device will only consume 2 uA however it is consuming...
After a few configuration issues we have finally got a connection with the asset tracker application. However we are not getting far enough to send data.
The log shows a...
Hello,
i am trying the nrfsniffer 3.0, but all the packets seems to being dropped.
I am using:
* BLE400 with nrf51822 module (firmware flashed with stlink )
* Linux...
I am trying to make couple templates for S113 with nRF52832 and nRF52840 with and without FreeRTOS and because there is no such in the examples, I’m not sure I made it right...
Hello,
I'm using SDK for Thread and Zigbee v4.1 and I developed a network using mqtt-sn library. Since the developed application requires data publishing at a high rate...
I want to get logs via RTT (JTAG) in the connectivity firmware example of SDKV15.
I have built the connectivity firmware project using cmake and opened the project in SES...
Hello
I'm trying to implement the click and double click and long click of a button in sdk v17.
Click and long click work fine. But double-click doesn't work.
Code...
Hi,
We are currently porting our code to the newest nRf5340 chip.
Everything goes fine when the target is secure (not ending with "ns" and not defining "CONFIG_TRUSTED_EXECUTION_NONSECURE...
Hi,
I am working on a device that has nrf52 as an additional BLE chip that does not run the main logic but provides UART over BLE to the application processor (NUS). In...
Hi,
I am working on the our customized board nRF52832 , interfaced with MAX30205 temperature sensor . I am advertising the data only when it reaches the below temperature...
