I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hello,
I am pretty new the BLE development stuff and was mostly working on an application that works with an existing connection. But because my colleagues are not able...
I am using nrf52832 ble, I want to set the pin P0.2 low as analog input and p0.3 high as analog input .
#define AIN0 2 // analog pin p0.2
#define AIN1 3
#define AIN0_PIN_CONFIG_HIGH...
SDK: 16
Mesh SDK: 410
Example: Light Lightness Server.
I discovered a bug when using the "Move Level" message that doesn't allow the LED to turn off after the move...
hello sir/ma'am
we are using nrf52840 chip in our customized board product and IAR as a development environment and also a debugger called segger jlink .we are not able...
Hello
we are thinking of using the nrf52832 (sdk 16.0, s132) , which we are a bit familiar with by now.
We have a project in which we need to transmit data to 150 unit...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1. I am using ‘ble_app_blinky’.
I am new to BLE certification. I have few queries on BLE Certification...
Hi Team,
I have down loaded the "pc-nrfutil-6.1.zip" from git repository and started the execution by using python commands. while running i am getting some errors.
...
Using PWM control 2.7KHZ buzzer, it can work normally when I don't turn on the broadcast. Every time I turn on the radio, the buzzer seems to blend in with different frequencies...
Hi
Based on zigbee sdk 3.2, add the device to the network, call zb_bdb_is_factory_new() after Joined network successfully, it returns true;
The same is true on zigbee...
Hello,
I am working with nRF52DK, I am trying to implement grouped SAADC for three sensors,
I want to receive all three ADC outputs at the same time on development kit...
Hello,
While working with a bare metal (no SoftDevice or OS) test application to prove code functionalities, I ran out in a weird behaviour that I cannot explain.
I'm...
Hi,
I started to implement the nrf ppm driver into my application. It is a smart connected grand light.
My goal is to smoothly fade the connected power LEDs on, hold for...
Hello,
So I have the following setup. I have an nrf9160 DK board. With the following hardware.
A base shield: https://www.reichelt.com/ch/de/arduino-shield-base-shield...
Hello,
I am using the att_mtu_max_throughput example from SDK 15. I am using an nRF52 as tester and nRF52840 DK as receiver.
I have modified the example slightly so that...
