Hi, I am Product Manager working for Medical Device Manufacturing company based out of Ireland.
we are in search for a development house / developer who will support us...
I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
Hello, i'm trying to build zephyr\samples\subsys\usb\cdc_acm but i get the following error:
1> zephyr/isr_tables.c does not exist. 1> Combining ‘zephyr/isr_tables.c’ 1>...
With very low data rates and short packets between two nRF52840s which of the following can operate at the lowest power?
1) ble peripheral to ble central uart
2) Enhanced...
Hello Dev
I'm working with MQTT sample on nRF9160 DK device and while that when I called facing some kernel based issue regarding k_sleep() function.
I'm getting this...
Hi,
Thanks for the help. I have run the proximity detection application in nRF52832 nordic thingy. Initially the LED was blinking in the thingy board but when I switched...
Hi,
Though the Thread CLI sample's 'README.rst' lists the following supported optional extensions, it does not specifically describe how to set the specific '.conf' files...
Hi everyone, Lately I have been using a PCA10040 (nRF52-DK) with J-Link OB-SAM3U128-V2-NordicSem V1.00 version. I'm trying to program two boards one with nRF51822_xxAA and...
Hi I am wondering what the best way to go about developing a RPi based system for presence detection with nordic ble devices
I would like to limit the bluetooth signal to...
Hello,
We are looking to do OTA device firmware update by GSM for the nRF52840.
We have a custom board with a nRF52840 and a GSM/LTE-M modem. They are communicating together...
SDK: 14.1.0
CHIP: nRF52840
CONFIG: ZIGBEE&BLE MULTI PROTOCOL
I wants to keep store zigbee pairing data after reset.
I setups like this.
After joining procedure...
From the gnss_extension.rst documentation shown below, it appears as thought the GNSS receiver can retain solution information from previous fixes/tracking in order to speed...
Hello Nordic!
I'm starting to develop my own Zigbee device with the nrf52840DK and I need to send some attributes to my coordinator, initially the door lock status is enough...
I am currently using an external JLINK to program the 9160 module, after adding read protection. Unable to recover using nrfjprog, report the following error:
ERROR: Recover...
Is there a version of the nRF Commandline tools that will run on an embedded Linux (ARM, RasberryPi compatible)? I specifically need the nrfjprog tool. The Segger tools do...
The v1.3 Product Specification datasheet for the nRF52833 lists the maximum source resistance on VBUS, including cable, as 2 ohms. Yet the same document recommends using a...
Hi,
As part of my internship, I am trying to modify an application and send the output of the application via CoAP. My goal is to modify the CoAP Client sample that comes...
