The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hi to all,
I am trying to do a ZUTH (Zigbee unified test harness) test run, using the Silabs devices as golden devices (as per CSA recommendation) and nRF 52840 dongles...
Hi
I am trying to port some PWM code from the NRF54L15 it uses HAL access because i have found it has faster writes which are useful for my application (testing latency...
Hello,
I have recently upgraded from v2.9 to v3.0.1 and have noticed that the mesh security has changed from CONFIG_BT_MESH_USES_TINYCRYPT to CONFIG_BT_MESH_USES_MBEDTLS_PSA...
Hello.
We're trying to expose and use the Wifi stack in micropython in our project for the nRF7002. We've managed to get Wifi scanning to work (based on the sample code...
Has anyone experienced the following error when Flashing (and debugging) from within VS Code. I have no idea what has happened, but it has hit several projects.
Even though...
Hi, I am trying to create a custom_service for my application.
I am using nRF52832 SDK_16
SES
I want to create the BLE_SERVICES
which has send characteristics and...
Hi,
I converted ble_app_beacon example to Segger Embedded Studio (using version 4.30b), as per the instructions in the link https://infocenter.nordicsemi.com/index.jsp?topic...
I configured a NRF52832 with non-scannable and non-connectable as well as scannable/connectable advertising. Everything is working fine.
But I want to fully understand the...
I have an existing phone app (using the traditional GATT system), and I would like mesh-enable my products so that if the products can see each other, then the phone can connect...
nRF51822 PS says standard drive GPIO output voltage will be VDD-0.3V ~ VDD In our previous project w/ nRF51822, I found it to be very close to VDD when connected to GND via...
Hi... i am using nRF52832 ,15.2 version sdk . I want to send the data from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can able to transmit the...
Hello,
I'm trying to setup an automated pairing for two devices. My peripheral device is advertising and should only allow connection requests from a specific central device...
I'm developing a multirole device to connect to a peripheral device that we developed earlier.
The multirole device when acting as a central device it scans for the peripheral...
To the kind attention of Nordic support team,
1. I have been using secured gazell library, where master is always polling in order to receive a message.
I was wondering...
Hi!
I'm developing a TCP server running on th e nRF9160, but there seem to be a problem with accepting clients. The code is very simple, just calls to socket, bind, listen...
Hi. I've developed a PCB with nRF52832 and I'm having problems with the circuit. When I put my hands closelly of P0.00(XL1) and P0.01(XL2) the bahavior of nRF changes... I...
I apologize if this was already answered elsewhere - I didn't find it.
I have been digging in the nRF52840 source code for the serial_nRF52840 SES project to understand...
Hello, I am trying to switch from BLE_GAP_PHY_AUTO to BLE_GAP_PHY_CODED in runtime, and I need to change central event length via sd_ble_cfg_set(). Whether is it possible...
Hi, i am working on servo motor using nrf52840 development kit , i want to run parallely four servo motors , i have merged the ble_app_uart+pwm library example ,
1. As of...
