Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
I am using the nRF5340 in our project. I am using both ports completely and I was unable to use the GPIOs after P1.11. When I debugged the issue I found that the GPIOs are...
Hi
We are using nRF9160 DK and I am able to transfer my data to BL652 via UART with P0.10 And P0.11 with use of This Example
But I get only One byte at a time so I read...
Hi,
I'm in the debugging stage for the beacon example on the nrf 52840. I have been assigned a task to measure the current on the SDK when the beacon is transmitting....
I am trying to enable ble_nus for wireless uart communication so I can send data from my device to a phone with the nordic app installed. I looked at the UART example and...
We have an nRF52-DK devboard and I have downloaded SDK 16 (nRF5SDK160098a08e2), and I am trying to build the project examples\ble_peripheral_ble_app_uart\pca10040\s112\arm5_no_packs...
Does the nRF5 SDK Scanning module support scanning extended advertising packets? For example to discover a Peripheral advertising using the Coded PHY?
When I try this, I...
The Problem
We have been struggling with what appears to be a rather fundamental issue using MQTT and eDRX on Verizon. We've investigated this quite heavily, with traces...
I am trying to flash the firmware on a device with NRFUTIL. When I run NRFUTIL.exe on a my windows 10 machine I get the error
This error occurs with both version 5.0.0...
Hi all,
I have the nRF9160 DK and I've just tried the out of the box demo (asset_tracker) following all the steps, but it didn't work because it seems that iBasis SIM does...
I have an ADXL362 eval board connected to a nRF52840-DK. When I try to read the device ID from the ADXL362 instead of returning 0xAD it most often returns 0x21 and at other...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hi All,
In nRFMesh app we can see the list of names of available Bluetooth devices. Is it possible to see the list of names of available Bluetooth devices using static provisioner...
According to the spec, this is how a bonded reconnect should work:
On first pass, the central client does discovery and enables descriptors to characteristics of interest...
Hi,
I've got an application based off the asset tracker firmware that needs a UART. From the many threads on the topic, I've found a way to shut down the UARTs to save power...
Hi,
I tried out the light client example in the Mesh SDK V4.0.0 and it works so far. Now
I added more data in the messages and it works, but only as long as the message...
