Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Serial Example in Mesh SDK allowed embedded system to provision a Mesh network
by interactive_pyaci.py controlling nRF52 with serial example with UART.
But the example...
Hi Nordic
SDK15.2 based application and bootloader running on NRF52840 based UBlox module.
We have the following symptoms happening in the field:
- 2 channels of the...
The customer wants to implement a hid function like the nrf52840 on the nrr9160, and there are no off-the-shelf routines or references to add the hid function.
Hi everyone,
I need your advice regarding the regulator configuration of nRF52840
I am designing my own PCB using Raytac's module MDBT50Q-1MV2 that carries on the nRF52840...
Is this the right cable to program the Thingy 91 using nRF9160-DK?
https://www.digikey.com/products/en/cable-assemblies/rectangular-cable-assemblies/450?k=adafruit%201675...
Hi,
I've developed a custom board with nRF5340-QKAA (see schematic sheet attached). nRF5340's VDD pins are not tied to VDDH pin, then I assume the nRF5340 automatically...
I tried to build the OpenThread CLI sample in nrfConnect SDK 3.1 with the version of Segger as installed by the ToolChain Manager. 4.52 on a nRF52840 DK board.
This is the...
Hi I am now aiming to progress ota with android application. Following the guidelines on ithub, I created a class DfuService, NotificationActivity. The class internal code...
Hi,
I am using nrf9160 module and want communicate with cloud via NB-iot network.
But I don't have idea that NB-iot supported in India or not.can you please help here...
Hi,
I'm trying to include a library written in C++ which requires at least GNU++11. Unfortunately if I switch the C++ compiler in SES I get the following error:
Is there...
Hi there, I have been trying recently to DFU a custom device using desktop nrf connect, and I get an error message as in the following picture right after pressing start DFU...
Hello,
Currently we working on a project that uses:
- nRF9160
- Zyphre OS
- Segger Embedded Studio for Arm (Nordic Edition) V4.52
- SDK v1.2
I saw in others...
Hello, i have configured the Timer1 as follows
ISR_DIRECT_DECLARE(timer_handler){
if (NRF_TIMER1->EVENTS_COMPARE[0]){ NRF_TIMER1->EVENTS_COMPARE[0] = 0;
gpio_pin_toggle...
Dear experts.. we are trying to build a 12 lead ecg system which sends real time data to mobile phone for plotting using nRF52832. While most of the time it works ok, when...
We have an application that sends a short BLE packet to a mobile app every second, for about 15 minutes, and then shuts down and sleeps. Meanwhile, it also writes to an SPI...
