Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hi,
From previous case , I still not fully understand how chip to retrieve the calibrated data from flash(already implemented read/write data for the interface by FDS),...
This question stems from this discussion
https://devzone.nordicsemi.com/f/nordic-q-a/71044/notifications-how-to-know-who-is-consuming-tx-buffers-most-efficient-way-of-sending...
The ARM Cortex-M4 supports many assembly-level DSP instructions and we would like to use them (not just the packaged ones in the CMSIS DSP libraries).
For example the set...
Hi All,
I want to use DFU to update the firmware from master to peripheral over BLE , both master and peripheral are nrf52840. My purpose is that the master sends a command...
Dear all:
My problem is described in the following steps：
1. Progranm the SoftDevice 7 (S132) into NRF52832, then program the ble_hid_keyboard example(SDK16) into NRF52832...
I'm using NRF52832 with S132_3.0.0 and the SDK version is 12.2.0.
When NRF53832 was bonded to a mobile phone, I try to use "pm_peers_delete()" to delete the bonding information...
I am looking for a way to start advertising as soon as connection event.
Our use-case is: we have 1 peripheral that's connected on CODED PHY to a central with a relatively...
Hi,
I am using softdevice s140_nrf52_7.0.1. I am trying to send the SAADC calculated voltage over NUS to a gateway. For like 20-30 seconds the program works fine and the...
Hello,
nRFSDK5 v16.0, device nRF52840, Softdevice v7.0.1
I am trying to write some data periodically onto device flash memory using FDS Lib, occasionally I come across...
Hello
I'm trying to reenable notifications on a characteristic from GATTS side
The device is 52810 running a custom service and this is the piece of code where i use ...
I am trying to pair my nRF52-DK with my Fitbit device for testing purposes. I am currently using the nRF Connect v3.6.1 desktop application. I can scan and connect to the...
When I run my code using Segger debugger, all is well and I can read and write from flash with issues. However, when I run the same code independently I sometimes get:
ASSERT...
For an ongoing product certification in China, I need to provide the certification lab with the Direct Test Mode application that is available from the nRF Connect suite on...
Hi,
I'm using the NRF52832, as peripheral, to read data from a HTS221 sensor via I2C.
I'm using the TWI_sensor module following this example , but I want it to enable...
