I am getting the following build errors when working with both DFU (MCUboot) and the file system (FAT FS) together. Errors: D:/ncs/v2.9.0/zephyr/drivers/disk/flashdisk.c:533...
Hi all,
Our company is currently prototyping with the Nordic 91X DK and looking to use both nrf cloud services specifically for using location services whilst also connecting...
nRF54L15 would be used as thread RCP, host processor would use uart to communicate with the rcp. They would behave like a OTBR.
I also need to do device firmware update...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
We're porting an nRFS52832 app from an earlier version (14) to 15.2. Using sd_ble_gap_device_name_set( &secMode, dN, len ) with a string of length=9 will only show 5 chars...
Hi, we are trying to get the nRF9160 connected to the internet again, we had it working 6 months ago.
Our hardware is 0.8.5
We are in Ireland where we only have NB-IOT...
Hi
I'm using the watchdog of the nRF52832 Rev. 1.
The PS V1.4 states that the maximum run current of the watchdog is 2uA while the typical current is only 0.3uA. Can you...
Hi,
I am migrating from SDK14.2 to SDK15.0 and I can compile now, but when runnning the nrfx_uart_init the hardware handshake signal RTS is high from the beginning.
...
I am running into compile errors in different places in the SDK where there are lines as shown below: #if (NRF_BLE_GATT_ENABLED) /* do something */ #endif It is a widely and...
Hello Team,
Currently, we are evaluating nRF52 using nRF52840DK for one of our upcoming project. Basically, our typical application involves sending 32 Bytes of command...
I am using nRF52840dk SDK15.3.0 ble_app_att_mtu_throughput example,in that example i included some part of ble_app_uart code. Now the issue i am facing is ble_link_ctx_manager...
im trying to do notification for characteristic of a service whenever i trying to notify from nrf mobile app the debug session in ses is stopping its play in few seconds
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Assume I have one FDS record. With this...
Hello,
If I understand well the characteristics of the Thingy.91 si that you supplie a firmware we can download and modify as we want because it is open source, is that...
We're trying to diagnose an issue that's occurred to at least two of our customers. For some reason, we've found two different iPhones that are seeing our reader (nRF52840...
Hello,
Float printk (%f and %0.2f) is not working. I use newlib and activated floats for print and scan support without success.
Configuration:
Version from 31 january...
Hello!
I use nRF52-DK wuth android device. DK connects to android device and works with it well. But I want a paired DK make unpaired from android device by performing unpair...
Hi,
I have requirement of BLE node to node communication in mesh network.
All the nodes should have single firmware which will be capable of publishing and subscribing...
