Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I am trying to add DFU to my project, so I merged in the code from the example in the SDK as follows:
I included the same .c files as the example project
I copied over...
Hi,
I did some measurements today on our I2C bus and see that the GND level is different some times. The most time it is not GND level (about 800mV). I checked cross talk...
Dear
I increated a Generic Level module to main elements which have a Generic ONOFF module on Mesh example Light Switch Server project base on PCA10056 DK board for nrf52840...
Hi I am using the example code here https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/nrfx_saadc_simple_low_power_app_timer_multichannel_oversample to use...
Hello guys,
Has anybody had the issue opening the new version of nRF Connect for Desktop (v3.6.1) in Windows 10 Pro. I have used an older version of this application and...
I want to build a secure boot loader for my custom board based on the nRF52832.
This post claims to walk through the process of building an example of a secure boot loader...
I'm strugglgin to find any documentation on how to set/request the iDRX paging interval in RRC idle. I have a device which sends an MQTT keepalive message every 3minutes,...
I have run into the issue where the soft device is not being processed when I debug so it throws the assertion failed error. After a lot of searching on the forum I came across...
We are using FDS from SDK 17.2.0 on nRF52832.
It is working so far, we can store and read back data.
When putting battery in and out fast, we get sometimes, but often...
I have the thingy52.py script running on a Raspberry Pi 4, and I can successfully poll the sensors when the Thing52 is awake (recently tapped) but when I try to poll in a...
In our final product, we wish to send the battery voltage level with other data to our server so that our customers can see how much the battery is drained. I am seeing that...
Hi,
I have downloaded the nrf5 Sdk 17.02 and nrf mesh 5.0.
Kit:nrf52832
Ide:segger ide
1. Can you list out the security related topics that I need to cover while using...
Hello! We're looking for a way to sync up several peripherals surrounding a central. Our idea was simple- have the central measure 'current time' as near to a connection as...
Hello,
I am working with the NRF52480 and started with SDK15.
I have reached a point where I would like to manipulate the value that is being written or read from a characteristic...
Hello,
In a quite particular configuration, the nRF8001 sometimes stops responding. The only way to make it work again is to do a hardware reset using the reset pin of the...
