Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
From Mesh Model v1.0.1 section 3.3.5.1 Generic Power OnOff Setup Server
"This model shall support model subscription, as defined in Section 4.2.3 of the Mesh Profile specification...
Hello Nordic!
I need to save dynamic arrays in NRF52840 flash using FDS, but after some days of trial and error I need to beg for help.
What I need to achieve is to have...
I'm trying to enable TWI in the eddystone example based on this article but I get the following compilation error:
nrfx/legacy/nrf_drv_twi.h:120:37: error: 'NRF_DRV_TWI_INSTANCE_0...
Hello,
I'm using nrf52832, sdk17 and Seeger Embedded Studio. I am using ble_app_uart example.
I am connecting with my phone and using RX and TX characteristics. My question...
Hello !!
I want to use Radio transmitter/ receiver example in my custom board which is used for BT remote control battery powered. I have added 10 buttons on my board and...
Hello NRF team,
We have been using NRF52832-QFAA based dev kit from Sparkfun, which has 512KB Flash / 64KB SRAM. I developed the app on Arduino whereas I flashed the bootloader...
Hello!
Here is a story I am sure you have heard before. I am evaluating the NRF9160DK and seeing what is the lowest power consumtpion we can get when sending data to a server...
I have an existing product using the nRF52832 SoC rev 1. We must transition to rev2 since rev1 is no longer sold. We use SDK12.0.0, with S132 V3.0.0. Have these software components...
Hello Team,
I have downloaded the Zephyr project and working on the LwM2M sample client application to make nRF52840 DK as an LwM2M client. I have followed the below link...
Hi,
Referring to White Paper nRF9160 Hardware Design Guidelines v1.0, what is the scenario (supply voltage, band, antenna VSWR, TX duty cycle...) behind maximum heat power...
Dear Sir,
I'm using nordic's example codes above to tx and rx, but i can not get them working properly. the LEDs should light on the receiver side according to the example...
I have a strange issue on the nRF9160-DK board using the nRF Connect SDK, GNU ARM for GCC v10.2.1, built using makefiles.
I have two threads that both wait on a semaphore...
Hi,
I am trying to change the tx power of Zigbee using the following APIs :
1) zb_set_tx_power(0x32); 2) nrf_radio_txpower_set(NRF_RADIO_TXPOWER_NEG12DBM); 3) nrf_802154_tx_power_set...
