Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello sir / ma'am
I want to implement OTA with zephyr using openthread but the size of my code .bin file is too much like 412kB .
How can I reduce my code size ?
What...
Hello
I am building a code with Openthread (NCS V1.4.0) and the size of that generated Bin file is 405kB. I would like to know why size of that file is more? I need to reduced...
Hi!
We are working with the nrf5340 on a custom board and we are trying to reduce its power consumption to the minimum possible. We have a beacon advertisement application...
Hi all,
I have just some issues with sd_flash_write and sd_flash_page_erase functions. I have created some code to read the temperature value and save this value in memory...
Hi,
I am considering nRF52 (most likely nRF52833 or 811 ) for a new design - curious how mature is the concurrent multiprotocol support in nRF52 - in particular for nRF52833...
Hi All,
We are using nRF52840 MCU and SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71. We are designing a device that uses switches connected to the below pins,
Pin...
Hi,
I use a custom board, softdevice and boot loader.
I use DFU to update a slave chip firmware. Everything goes right until we invalidate and write flash :
// Invalidate...
Hi
i use sdk 17.02
custom board
soft device
when i program input digital pin I have an extra consumption of arounf 9µA versus not using it.
Could you tell me if...
Hello,
I am using FDS successfully with SDK 17.0.2, secure bootloader and softdevice. Bluetooth (BLE) environment, if it does matter.
I can read and write data. But following...
hi guys
i develop mobile app for iOS and use nrfMesh lib v3.0-beta1. i have few nodes subscribed to a group. I send GenericLevelSet message to a group and receive successful...
if a response to the http request is chunked ( https://en.wikipedia.org/wiki/Chunked_transfer_encoding ), it is not handled correctly by the serial_lte_modem.
Sometimes...
This should not be so hard - have to go here and wait until this gets answered.
1. I can't find an SDK consistent with SoftDevice s110.
2. I have an nRF51822 production...
I want to find out BLE throughput.
Throughput_bps = num_packets * (ATT_MTU - 3) * 8 / seconds.
In this equation, how can I find out num_packets?
Also, ATT_MTU =...
Hello,
I was just wondering that if somehow we can send the AGPS code data of thingy 91 to adafruit server through the MQTT just for testing purposes.
Let me know...
